General EDM Discussion


Page 1 of 18 1234 11 ... LastLast
Threads 1 to 20 of 354

Forum: General EDM Discussion

Discuss building, operating EDM machines here!

  1. Need Help!- Z axis torque alarm

    Started by WEDDLETON‎, 03-18-2017 12:04 AM
    alarm, axis, grease, happen, torque
    • Replies: 1
    • Views: 118
    03-20-2017, 07:22 AM Go to last post
  2. Need Help!- Charmilles Roboform 30 1995 Year. Cabin door open error.

    Started by ascxc‎, 03-15-2017 10:30 AM
    cabin, door, error, open, year
    • Replies: 0
    • Views: 95
    03-15-2017, 10:30 AM Go to last post
  3. Need Help!- Buying a new die sinker EDM

    Started by chowsiusing‎, 03-14-2017 05:09 AM
    die, edm, machine, machines, sinker
    • Replies: 0
    • Views: 74
    03-14-2017, 05:09 AM Go to last post
  4. Question Wiring Confusion Mitsubishi DWC 90 SB Wire EDM

    Started by prototyperbob‎, 07-03-2015 02:47 PM
    • Replies: 2
    • Views: 419
    03-13-2017, 07:31 PM Go to last post
  5. Charmilles Robofil 200 -- need help diagnosing

    Started by 1000ee-monarch‎, 03-05-2017 08:01 PM
    charmilles, drive, floppy, guessing, robofil
    • Replies: 1
    • Views: 152
    03-06-2017, 10:24 AM Go to last post
    • Replies: 0
    • Views: 81
    03-04-2017, 11:55 AM Go to last post
  6. Help with Agie Mondo 20

    Started by Jazper‎, 02-20-2017 02:03 PM
    agie, agie cut, agiecharmilles, axis, home
    • Replies: 1
    • Views: 159
    02-26-2017, 10:15 AM Go to last post
  7. Need Help!- I need, Software for machine AGIE 150 hss

    Started by joanlaga‎, 02-23-2016 07:07 AM
    agie, agie 150, hss, machine, software
    • Replies: 1
    • Views: 368
    02-15-2017, 11:52 PM Go to last post
  8. Need Help!- 1998 Mits FX10K start up with rotary phase converter

    Started by Jg-gonzo‎, 02-04-2017 01:42 PM
    company, leg, legs, machine, run
    • Replies: 1
    • Views: 168
    02-09-2017, 09:14 AM Go to last post
  9. Need Help!- Mitsubishi DWC90HA Wire Contact Light always on

    Started by GEC-ENG‎, 01-31-2017 02:21 PM
    • Replies: 0
    • Views: 215
    01-31-2017, 02:21 PM Go to last post
  10. Problem- Mitsubishi wire edm water level dropping in working tank

    Started by cuonghuy‎, 01-24-2017 12:19 PM
    tank, time, water, work, working
    • Replies: 0
    • Views: 257
    01-24-2017, 12:19 PM Go to last post
  11. Mits FX10 & 20 maint. issues

    Started by tvalen1432‎, 01-13-2017 03:32 AM
    atf, fx10, maintenance, mits fx10/fx20, solenoid valve
    • Replies: 1
    • Views: 272
    01-16-2017, 03:01 AM Go to last post
  12. Just In 1995 Charmilles Roboform 2000 for sale

    Started by scottlj‎, 01-12-2017 07:02 PM
    case, charmilles, machine, power, roboform
    • Replies: 0
    • Views: 166
    01-12-2017, 07:02 PM Go to last post
  13. Need Help!- INformation about small hole drill EDM - BAOMA BDM703

    Started by peloflex‎, 01-12-2017 11:13 AM
    drill, edm, hole, machine, small
    • Replies: 0
    • Views: 146
    01-12-2017, 11:13 AM Go to last post
  14. Roboform 810 FDD Emulator

    Started by dan61t‎, 01-05-2017 06:51 PM
    drives, loading, roboform, software, usb
    • Replies: 0
    • Views: 181
    01-05-2017, 06:51 PM Go to last post
  15. Need Help!- Rectangle and cycle shap cutting problem

    Started by mithu‎, 12-31-2016 01:51 AM
    5mm, cnc, cut, cycle, square
    • Replies: 0
    • Views: 268
    12-31-2016, 01:51 AM Go to last post
  16. Need Help!- Programming wire edm

    Started by Danny1203‎, 11-30-2016 07:11 PM
    edm, main, program, wire edm, wire machining
    • Replies: 0
    • Views: 370
    11-30-2016, 07:11 PM Go to last post
  17. Question Need Help!- Roboform 550 Slow Tank Fill

    Started by WesO‎, 04-26-2016 10:43 AM
    floats, problem, pump, roboform, sinker edm
    • Replies: 2
    • Views: 412
    11-26-2016, 12:33 PM Go to last post
  18. Need Help!- Mitsubishi FX20 contact problem

    Started by Pete_MP_Mold‎, 11-15-2016 11:57 PM
    contact, mitsubishi, power, settings, show
    • Replies: 4
    • Views: 297
    11-18-2016, 11:09 AM Go to last post
  19. Need Help!- WIRE machine - Fanuc Matra Tape Cut model I

    Started by dzcatic‎, 11-04-2016 05:23 PM
    • Replies: 1
    • Views: 345
    11-11-2016, 09:06 PM Go to last post

Page 1 of 18 1234 11 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands