G41, how do i use it?

[Vegabond]

Hello.

I try to use the G41, but i have some problems.
If someone can see on my g-code i have attached, and see whats wrong.
Im a beginner on the iso programming

I heard i can`t run G41 before a z manouver?

Can someone tell me something about it?


%
N1O7(Strekkstav type 2 i to kutt)
N2G0G17G40G80G90M5M9
N3T7M6
N4X48.Y-15.E1S2000M3
N5Z20.D7H7
N6G1F1000.
N7(Kutt nr 1)
N7Z-2.
N8G41
N9y-5.35
N9X21.31
N10G3R+6.X17.Y-3.35
N11X-17.
N12G3R+6.X-21.31Y-5.35
N13X-48.
N14G0Z25.
N15G40
N16G0Y20.
N17G1Z-2.
N8G41
N9y5.35
N9X-21.31
N10G3R+6.X-17.Y3.35
N11X17.
N12G3R+6.X21.31Y5.35
N13X48.
N6(Kutt nr 2)
N7Z-2.
N8G41
N9y-5.
N9X21.47
N10G3R+6.X17.Y-3.
N11X-17.
N12G3R+6.X-21.47Y-5.
N13X-48.
N14G0Z25.
N15G40
N16G0Y20.
N17G1Z-2.
N8G41
N9y5.
N9X-21.47
N10G3R+6.X-17.Y3.
N11X17.
N12G3R+6.X21.47Y5.
N13X48.
N26(ENDING PROGRAM
N27G0G80G90M5M9
N28Z0G53
N29X0Y200.Z0E0H0
N30M30
%

Attach the DWG too....


Greetings from Robert.

[mopar]

N1O7(Strekkstav type 2 i to kutt)
N2G0G17G40G80G90M5M9
N3T7M6
N4X48.Y-15.E1S2000M3
N5Z20.D7H7
N6G1F1000.
N7(Kutt nr 1)
N7Z-2.
N9G41 y-5.35
N9X21.31



OR


N1O7(Strekkstav type 2 i to kutt)
N2G0 G17 G40 G80 G90 M5 M9
N3 T7 M6
S2000 M3
N6 G1 G41 X 48. Y-15. E1
N5 Z 2. D7 H7
F1000.(HA HA )
N7 (Kutt nr 1)
N7 Z-2.
N9 y-5.35
N9 X21.31

[Vegabond]

F1000.(HA HA )

I talk in mm........

[beege]

What control? Generally, you can move Z before, during and after employing a G41. G41 (cutter compensation left) is usually initiated on the first move into the contour, perpendicular to the first element, in a straight line of a length greater than the cutter radius if you intend on offsetting the tool by the radius of the tool. Most controllers will not like more than three lines of non-planar (XY for G17), because of read-ahead calculations.

[sinha_nsit]

Cannot use two consecutive Z-moves after G41/42.