Need Help!- inside arcs with comp doing "loop de loops"

[Mikey69]

Whenever I do an inside arc on my FANUC 10m, I get full circles then it goes on it's way to do the program as programmed.

It happens with I, J, and R.

I recently accidently erased all my parameters and re-entered them through a parameter list from leadwell

[dcoupar]

Why not post an example of the code so we can take a look?

[Mikey69]

Originally Posted by dcoupar Why not post an example of the code so we can take a look?

%
O100
(MTOOL T9 S1 D.5 H5. DIAM_OFFSET 9 = .25)


G90 G80 G40 G20 G17

G00 G91 G28 Z0.
G91 G28 X0. Y0.


T9 M06
S374 M3
G00 G90 G54 X-.3 Y0.
M01
G43 H9 Z.1 M08
G01 Z-.5 F.9
G42 D59 Y.3 F50.
G02 X0. Y0. I0. J-.3
G01 Y-2.
X.4
G03 X.5 Y-1.9 I0. J.1
G01 Y-1.8
G02 X.8 Y-1.5 I.3 J0.
G01 X1.9
G03 X2. Y-1.4 I0. J.1
G01 Y-.6
G03 X1.9 Y-.5 I-.1 J0.
G01 X.8
G02 X.5 Y-.2 I0. J.3
G01 Y-.1
G03 X.4 Y0. I-.1 J0.
G01 X0.
G02 X-.3 Y.3 I0. J.3
G40 G01 X0.
G90 G00 Z.1
G91 G28 Z0. M05
G91 G28 X0. Y0.
G90
M30
%

[dcoupar]

Does it do this on the lead-in G02 arcs also? I assume it worked properly before the parameters were erased?

[Mikey69]

Originally Posted by dcoupar Does it do this on the lead-in G02 arcs also? I assume it worked properly before the parameters were erased?

Yes, any arc where the cutter's 'inside' the arc.

[Mikey69]

I found it!!!

Param 6010 was too high!!! I'll run a few programs and see how it goes.

[dcoupar]

Way to go!

[Mikey69]

Originally Posted by dcoupar Way to go!

I get a little apprehensive with just plugging away. Idon't want to wreck anything.

Are you familiar with parameters for spindle gear selection?

Up to 1000 RPM, my speed quadruples. Over 1000 (even 1000.5), it's just fine.

[dcoupar]

My 10M manual is 180 miles away, sadly. I'll take a look when I get home this evening. What make/model machine is this?

[Mikey69]

Originally Posted by dcoupar My 10M manual is 180 miles away, sadly. I'll take a look when I get home this evening. What make/model machine is this?

Leadwell
Model MCV 550D
Series: 865282
Mfg. Date: Jan 1986
Fanuc 10MA
Mfg. No: 5983

I need the spindle speed parameters. They are 5600 to 6000

[dcoupar]

Just out of curiosity, have you contacted Leadwell? They may have copies of the parameter list for that machine.

[Mikey69]

Originally Posted by dcoupar Just out of curiosity, have you contacted Leadwell? They may have copies of the parameter list for that machine.

I have a copy they sent me. It's missing the spindle ratios, though.