Page 1 of 2 12 LastLast
Results 1 to 12 of 18

Thread: Fanuc OM-C pmc problem

  1. #1
    rai
    rai is offline
    Registered
    Join Date
    Feb 2006
    Location
    INDIA
    Posts
    179
    Downloads
    0
    Uploads
    0

    Exclamation Fanuc OM-C pmc problem

    Hi
    I have a Kaffo VMC1200 equiped with fanuc OM-C cnc system with PMC-M on slave. Right now I facing a problem of the PMC. Whenever I switch on the system, during boot screen, I am getting a message "slave ready waiting for PMC" & then not ready being appeared on the screen.
    I am not familier with PMC-M card on slave. although I had interfaced couple of Fanuc OM with PMC-L but PMC-M new for me. I donot know how to interface PMC-M card. Even I donot have it's connection manual & drawing.
    Kindly help me to solve this problem & send me it's manual.


  2. #2
    rai
    rai is offline
    Registered
    Join Date
    Feb 2006
    Location
    INDIA
    Posts
    179
    Downloads
    0
    Uploads
    0
    Still waiting for someone's reply, please help me. atleast send me connection manual hardware or pmc-M card details.


  3. #3
    Registered
    Join Date
    Jan 2007
    Location
    Hamilton,Oh
    Posts
    333
    Downloads
    0
    Uploads
    0
    I get "Not Ready" when my e-stop button is pressed.
    Can you edit a program?
    Can you get to the 700 series diagnostics?


  4. #4
    rai
    rai is offline
    Registered
    Join Date
    Feb 2006
    Location
    INDIA
    Posts
    179
    Downloads
    0
    Uploads
    0
    Only not ready is being appeared on the screen & nothing happen like, mode selection, etc. As system shows during boot slave ready waiting for pmc. I think PMC-M card is not communicate with cnc. I donot have PMC-M card details & it's manual for futher diagnostics. Please help me.


  • #5
    Registered
    Join Date
    Aug 2007
    Location
    THAILAND
    Posts
    21
    Downloads
    0
    Uploads
    0

    Smile Cnc Service

    It is very hard to say that it came from this card, some time Master card, PSU, Fuse and 24v shorted ground and so on . I think better you call Fanuc local service for this problem. I have connecting manual for this if you want email me at k_amnaj@yahoo.com. It is very big file around 5.8MB.
    Thanks


  • #6
    Registered
    Join Date
    Jan 2007
    Location
    Hamilton,Oh
    Posts
    333
    Downloads
    0
    Uploads
    0
    My manual discusses PMC-M with "I/O Link" and without "I/O Link".
    Which is your setup?


  • #7
    rai
    rai is offline
    Registered
    Join Date
    Feb 2006
    Location
    INDIA
    Posts
    179
    Downloads
    0
    Uploads
    0
    Quote Originally Posted by bborb View Post
    My manual discusses PMC-M with "I/O Link" and without "I/O Link".
    Which is your setup?
    It's PMC-M with I/O link. I think so but not sure. PMC I/O card is mounted seperately from mother board.


  • #8
    rai
    rai is offline
    Registered
    Join Date
    Feb 2006
    Location
    INDIA
    Posts
    179
    Downloads
    0
    Uploads
    0
    please help me , atleast send me it's manual.


  • #9
    rai
    rai is offline
    Registered
    Join Date
    Feb 2006
    Location
    INDIA
    Posts
    179
    Downloads
    0
    Uploads
    0
    Still waiting for someone's help, please help me , atleast send me it's manual.


  • #10
    Registered
    Join Date
    Aug 2007
    Location
    THAILAND
    Posts
    21
    Downloads
    0
    Uploads
    0

    PMC Problem

    Check your email of both guys, I have sent them and some basic procedure for you.
    Thanks!


  • #11
    Registered
    Join Date
    Apr 2006
    Location
    USA
    Posts
    190
    Downloads
    0
    Uploads
    0
    If you have a back up copy of the parameters I would try dumping the system and reloading.
    To do this power up holding in "RESET" and "DELETE" pushbuttons


  • #12
    rai
    rai is offline
    Registered
    Join Date
    Feb 2006
    Location
    INDIA
    Posts
    179
    Downloads
    0
    Uploads
    0
    Quote Originally Posted by CNC SERVICE View Post
    Check your email of both guys, I have sent them and some basic procedure for you.
    Thanks!
    I did not receive your mail, please send me again.
    ahe_303@rediffmail.com


  • Page 1 of 2 12 LastLast

    Similar Threads

    1. Fanuc 21i-T DNC Problem
      By Stebedeff in forum Fanuc
      Replies: 4
      Last Post: 07-16-2007, 04:00 PM
    2. Fanuc OT problem
      By Skybrake in forum Fanuc
      Replies: 16
      Last Post: 02-09-2007, 01:04 AM
    3. Fanuc 6M Problem
      By Mimas in forum Fanuc
      Replies: 3
      Last Post: 12-16-2006, 07:03 PM
    4. Fanuc 0M problem
      By bauhar in forum Fanuc
      Replies: 6
      Last Post: 09-11-2006, 11:01 PM
    5. Fanuc 5 problem
      By jevs in forum Fanuc
      Replies: 3
      Last Post: 02-21-2005, 08:36 PM

    Posting Permissions


     


    About CNCzone.com

      We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

    Follow us on

    Facebook Dribbble RSS Feed


    Search Engine Friendly URLs by vBSEO ©2011, Crawlability, Inc.