FANUC 15M E-stop during ATC on Matsuura MC-1000V


Results 1 to 9 of 9

Thread: FANUC 15M E-stop during ATC on Matsuura MC-1000V

  1. #1
    Registered
    Join Date
    Dec 2005
    Location
    US
    Posts
    285
    Downloads
    0
    Uploads
    0

    Default FANUC 15M E-stop during ATC on Matsuura MC-1000V

    Today accidentally I e-stopped the machine during a tool change. Now I have a mess. New tool is in the spindle, old tool is hanging down, and the arm looks nearly home, if not home. Dumb me, I shut the machine down and now it wants to home before anything.

    These are my current messages:
    3000 Sequence time over check the next seq number, Seq 16 In motion of ATC(M06)
    3001 Return to zero position each axis after power on.
    3003 ATC Arm is not at home position. Return the arm to home position and set the tool number.

    The manual indicates if I set "PC Paramter K11, 6 (ATCTSM) to 1" I should get #3045 ATC Trouble-Shooting Mode.

    K11 read 00000001 so I changed it to 01000001 but I haven't had the ATC Trouble-Shooting Mode appear to activate. I think my power cycle created a chicken before the egg scenario. Unless of course I'm setting the wrong bit.

    Any ideas how I can get this arm re-homed?

    Similar Threads:


  2. #2
    Registered
    Join Date
    Dec 2005
    Location
    US
    Posts
    285
    Downloads
    0
    Uploads
    0

    Default Re: FANUC 15M E-stop during ATC on Matsuura MC-1000V

    I toggled b3 of K00 to enable Zero Return Neglect, now I see the #3045 ATC Trouble-shooting Mode in messages. Unfortunately the jog feed buttons don't appear to do anything. They are suppose to move the arm in atc troubleshooting mode. Any ideas how to enable the jog?



  3. #3
    Registered
    Join Date
    Dec 2005
    Location
    US
    Posts
    285
    Downloads
    0
    Uploads
    0

    Default Re: FANUC 15M E-stop during ATC on Matsuura MC-1000V

    I have it fixed. The PO had made some timing marks on the arm index plate... I lined them up and the error cleared. I'm back up and running.

    Never could get the arm jog function to work. Maybe it was been due to the pocket being down? I'd be interested to know if anyone has experience jogging these arms.



  4. #4
    Registered jorber's Avatar
    Join Date
    Apr 2004
    Location
    Dominican Rep
    Posts
    45
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by forhire View Post
    I have it fixed. The PO had made some timing marks on the arm index plate... I lined them up and the error cleared. I'm back up and running.

    Never could get the arm jog function to work. Maybe it was been due to the pocket being down? I'd be interested to know if anyone has experience jogging these arms.
    I have almost the same problem, I don’t have any manual for this machine and I am getting the the error 3000 sequence time over seq 15 in motion of ATC(M06)
    In the diagnostic I checked and all the input are where they must be
    I don’t know how to reset this sequence! Any ideas?

    Jorge B.
    jorbercnc.com


  5. #5
    Registered jorber's Avatar
    Join Date
    Apr 2004
    Location
    Dominican Rep
    Posts
    45
    Downloads
    0
    Uploads
    0

    Default Re: FANUC 15M E-stop during ATC on Matsuura MC-1000V

    Quote Originally Posted by forhire View Post
    Today accidentally I e-stopped the machine during a tool change. Now I have a mess. New tool is in the spindle, old tool is hanging down, and the arm looks nearly home, if not home. Dumb me, I shut the machine down and now it wants to home before anything.

    These are my current messages:
    3000 Sequence time over check the next seq number, Seq 16 In motion of ATC(M06)
    3001 Return to zero position each axis after power on.
    3003 ATC Arm is not at home position. Return the arm to home position and set the tool number.

    The manual indicates if I set "PC Paramter K11, 6 (ATCTSM) to 1" I should get #3045 ATC Trouble-Shooting Mode.



    Any ideas how I can get this arm re-homed?
    Also, is it posible to have a copy of that procedure from your manual?


    Enviado desde mi iPhone utilizando Tapatalk

    Jorge B.
    jorbercnc.com


  6. #6
    Registered
    Join Date
    Dec 2012
    Location
    The Netherlands
    Posts
    199
    Downloads
    0
    Uploads
    0

    Default Re: FANUC 15M E-stop during ATC on Matsuura MC-1000V

    Hi,

    Found a pdf for a Matsuura MC-500V, maybe it works for your machine also.

    https://wiki.artisansasylum.com/imag...00V_Manual.pdf

    Regards,
    Heavy_Metal

    Attached Thumbnails Attached Thumbnails FANUC 15M E-stop during ATC on Matsuura MC-1000V-matsuura-mc-500-v-page-114-jpg   FANUC 15M E-stop during ATC on Matsuura MC-1000V-matsuura-mc-500-v-page-115-jpg  


  7. #7
    Registered jorber's Avatar
    Join Date
    Apr 2004
    Location
    Dominican Rep
    Posts
    45
    Downloads
    0
    Uploads
    0

    Default Re: FANUC 15M E-stop during ATC on Matsuura MC-1000V

    Hi, thanks for the manual, but I think is different control
    I set everything in home position but still getting that message



    Enviado desde mi iPhone utilizando Tapatalk

    Jorge B.
    jorbercnc.com


  8. #8
    Registered
    Join Date
    Dec 2005
    Location
    US
    Posts
    285
    Downloads
    0
    Uploads
    0

    Default Re: FANUC 15M E-stop during ATC on Matsuura MC-1000V

    Matsuura sent me scans of three manuals. The one you need is the maintenance manual. Send me a PM with your email address.
    T214 MC-1000V7-MNTE-E-02_15M AUG1990.pdf
    T214 MC-1000V7-OPERATOR-E-02_15M AUG1990.pdf
    T221 MC-1000V7-PROGRAM-E-01_OM JAN1991.pdf



  9. #9
    Registered jorber's Avatar
    Join Date
    Apr 2004
    Location
    Dominican Rep
    Posts
    45
    Downloads
    0
    Uploads
    0

    Default Re: FANUC 15M E-stop during ATC on Matsuura MC-1000V

    Quote Originally Posted by forhire View Post
    Matsuura sent me scans of three manuals. The one you need is the maintenance manual. Send me a PM with your email address.
    T214 MC-1000V7-MNTE-E-02_15M AUG1990.pdf
    T214 MC-1000V7-OPERATOR-E-02_15M AUG1990.pdf
    T221 MC-1000V7-PROGRAM-E-01_OM JAN1991.pdf
    I got them, thanks!


    Enviado desde mi iPhone utilizando Tapatalk

    Jorge B.
    jorbercnc.com


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

FANUC 15M E-stop during ATC on Matsuura MC-1000V
FANUC 15M E-stop during ATC on Matsuura MC-1000V