Takisawa TC-1 Fanuc 0-TC


Page 1 of 2 12 LastLast
Results 1 to 20 of 24

Thread: Takisawa TC-1 Fanuc 0-TC

  1. #1
    Registered Dave1's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    156
    Downloads
    0
    Uploads
    0

    Default Takisawa TC-1 Fanuc 0-TC

    Hello all!
    New to these forums, great info I've seen posted. I do have a question however. I have recently purchased a Takisawa TC-1 with a Fanuc 0-TC control. I am waiting patiently for an Operators manual from ebay and a programming manual from Fanuc America. What other manuals are suggested? Is there actually a parameter manual? One thing I did find out when programming a M68 (collet close) it waits for something, the command does not cancel. M69 however, works fine. Opens the collet and cancels itself. I've tried it in MDI, within a program to no avail. The parameter page looks greek to me, not what I'm used to plus I have no explaination on what numbers mean what. Also looks to be Binary?
    Thanks in advance,
    Dave
    (Schneider Machine)
    (A force of one)

    Similar Threads:


  2. #2
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    24216
    Downloads
    0
    Uploads
    0

    Default

    Some M codes require confirmation, could be a pressure switch depending on the method the collet is closed.
    There is a Description manual
    Connection manual
    Programming manual
    Operators Manual
    Maintenance Manual
    Parameter Manual.
    Operation & Maintenance Manual.
    Then there is the MTB Manual for the Machine control and M codes etc.
    Al.

    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  3. #3
    Registered Dave1's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    156
    Downloads
    0
    Uploads
    0

    Default

    Thank you Al,
    I can change the clamp via the key switch to internal or external. That in turn reverses the commands. M68 now opens the collet and cancels itself. M69 on the other hand will not cancel. So, what ever it's waiting for is unknown as the problem changes

    What manuals in the list do you recommend, what will I get the most bang for the buck out of? Besides the operators manual and programming manual because they are already on the way.

    Thanks again,
    Dave

    Schneider Machine
    A force of one


  4. #4
    Registered Dave1's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    156
    Downloads
    0
    Uploads
    0

    Thumbs up

    OK!!!!! Found the pressure switch. I Adjusted it lower and the m68 code will cancel, I feel kinda stupid. This is my first hydrolic machine, used to pneumatic ones. Soon I will learn the idiosyncrasy's of this dang thing, after all, it's what keeps it interesting.
    Dave

    Schneider Machine
    A force of one


  5. #5
    Registered jackson's Avatar
    Join Date
    Oct 2006
    Location
    United States
    Posts
    586
    Downloads
    0
    Uploads
    0

    Default

    Chuck pressure will also cause your clamp un clanp to move slower primairly your clamp, not much slower but you can tell,

    individual who perceives a solution and is willing to take command. Very often, that individual is crazy.


  6. #6
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    24216
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by Dave1 View Post
    What manuals in the list do you recommend, what will I get the most bang for the buck out of?
    Dave
    Send me a PM with an email address, some exceed the server capacity though.
    Al.

    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  7. #7
    Registered Dave1's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    156
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by Al_The_Man View Post
    Send me a PM with an email address, some exceed the server capacity though.
    Al.
    Done,
    Thanks Al,

    Dave

    Schneider Machine
    A force of one


  8. #8
    Registered Dave1's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    156
    Downloads
    0
    Uploads
    0

    Default

    The programming manual from Fanuc America showed up on friday, sheese, does a person need a PHD and a Doctorate degree to understand the dang thing

    Today the manual from ebay showed up, sweet, wish I'd got that first
    Now it's time to do some tool block making, some reading, some programming, and some testing, but from what I gather the machine setting and tool settings are not what I'm used to. Seems confusing. Oh, it's not a G54 machine, it's a G50?????

    Dave

    Schneider Machine
    A force of one


  9. #9
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    24216
    Downloads
    0
    Uploads
    0

    Default

    See if you have parameter 910 bit #1 set (xxxxxx1x)
    This should be G54~59
    Al.

    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  10. #10
    Registered Dave1's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    156
    Downloads
    0
    Uploads
    0

    Default

    Al, that parameter is set to 0, I did try and change it to 1 and got 2 alarms, 401 and 430? I set it back.
    Dave

    Schneider Machine
    A force of one


  11. #11
    Registered
    Join Date
    Oct 2008
    Location
    India
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default

    Dear All,
    I have takisawa tc-1 with fanuc o-tc controler.
    my problem was few day ago the Dignotics parameters are lots.
    so please can help me,
    anybody have same machine. please sand me a this parameters.

    thanks in advance
    nilesh patel



  12. #12
    Registered Dave1's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    156
    Downloads
    0
    Uploads
    0

    Default

    Nilesh,
    You have a private message
    Dave

    Schneider Machine
    A force of one


  13. #13
    Registered
    Join Date
    Dec 2004
    Location
    USA
    Posts
    167
    Downloads
    0
    Uploads
    0

    Default

    the part number for the Fanuc OT parameter manual is B-62550En/01 .....it just happen to be sitting on my desk

    matt



  14. #14
    Registered
    Join Date
    Apr 2009
    Location
    Croatia
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default Re: Takisawa TC-1 Fanuc 0-TC

    Best regards to everyone,

    I bought Takisawa TC-1.
    I would ask you if someone has operator manual, wirring manual...
    My e-mail adress f1000@email.t-com.hr;
    Thanks
    Tom



  15. #15
    Member
    Join Date
    Dec 2013
    Posts
    267
    Downloads
    0
    Uploads
    0

    Default Re: Takisawa TC-1 Fanuc 0-TC

    I also picked up a Takisawa TC-1 last week. My first CNC lathe, so any docs you guys have gathered up for this machine would help me greatly! Please shoot me a private message if you wouldn't mind sharing any soft copies you have.

    Any specific advise would also be helpful. My machine is a 10HP, 8 tool turret, hydraulic 3 jaw chuck came on the machine (I might look into picking up a collet chuck also if you guys have any advice on which to get).



  16. #16
    Registered
    Join Date
    May 2010
    Location
    malaysia
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: Takisawa TC-1 Fanuc 0-TC

    hi all,

    anyone here have takisawa TC1 CNC Lathe Fanuc OT parameter. My machine parameter lost recently and appear a lot alarm.





    通过我的 SM-G750F 上的 Tapatalk发言



  17. #17
    Registered
    Join Date
    Apr 2009
    Location
    Croatia
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default Re: Takisawa TC-1 Fanuc 0-TC

    Dear Mr. Darren75 ,
    Yes I have takisawa TC-1.
    What year is your machine?
    I have saved the machine parameters
    f1000@email.t-com.hr



  18. #18
    Registered
    Join Date
    May 2010
    Location
    malaysia
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: Takisawa TC-1 Fanuc 0-TC

    Quote Originally Posted by cnc wedm View Post
    Dear Mr. Darren75 ,
    Yes I have takisawa TC-1.
    What year is your machine?
    I have saved the machine parameters
    f1000@email.t-com.hr
    my machine was year 1993. can sent to me by email
    enixme@gmail.com

    thanks a lot

    通过我的 SM-G750F 上的 Tapatalk发言



  19. #19
    Registered
    Join Date
    Apr 2009
    Location
    Croatia
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default Re: Takisawa TC-1 Fanuc 0-TC

    Dear Mr. Darren,
    I sent you email from gmail account.
    cnc wedm



  20. #20
    Member bip1988's Avatar
    Join Date
    Sep 2021
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default Re: Takisawa TC-1 Fanuc 0-TC

    Good evening all, first time on here.
    I have a 1993 TC-1 had its parameters deleted. I have all the parameters except for the PMC parameters 900-939. If anyone has a copy it would be much appreciated.
    Regards
    Brad.



Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Takisawa TC-1 Fanuc 0-TC

Takisawa TC-1 Fanuc 0-TC