Results 1 to 11 of 11

Thread: fanuc 10, 11, 12 PMC parameters upload via RS232

  1. #1
    Registered guhl's Avatar
    Join Date
    Aug 2007
    Location
    Ukraine, Sevastopol
    Posts
    503
    Downloads
    0
    Uploads
    0

    Default fanuc 10, 11, 12 PMC parameters upload via RS232

    is it possible to upload PMC parameters from Fanuc 10, 11, 12 via RS232?

    Similar Threads:
    Last edited by guhl; 10-28-2013 at 08:26 AM.
    New location: Sevastopol, Crimea, Russia.


  2. #2
    Registered
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    349
    Downloads
    0
    Uploads
    0

    Default

    The procedures are here: Fanuc 10 Fanuc 11 Memory Backup Procedures
    Now don't forget to write down 9100 to 9199, then just use a binary to hex calculator such as Binary to Hex Converter and OP1, OP2 ,OP3 in the list to input those parameters will correspond to 9100, 9101, 9102 etc.

    Cheers.

    Last edited by botha.y; 10-28-2013 at 02:38 PM.


  3. #3
    Registered guhl's Avatar
    Join Date
    Aug 2007
    Location
    Ukraine, Sevastopol
    Posts
    503
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by botha.y View Post
    The procedures are here: Fanuc 10 Fanuc 11 Memory Backup Procedures
    Now don't forget to write down 9100 to 9199, then just use a binary to hex calculator such as Binary to Hex Converter and 0, 1, 2 ,3 will correspond to 9100, 9101, 9102 etc.

    Cheers.
    I mean via RS232, so as there are a lot of data tables in my PMC, it's difficult to write down so much information on a paper

    New location: Sevastopol, Crimea, Russia.


  4. #4
    Registered
    Join Date
    Apr 2009
    Location
    Canada
    Posts
    674
    Downloads
    0
    Uploads
    0

    Default

    NO.



  5. #5
    Registered
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    349
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by guhl View Post
    I mean via RS232, so as there are a lot of data tables in my PMC, it's difficult to write down so much information on a paper
    Err... that's the actual procedures with RS232, you just punch your PMC parameters to save them and read them to load them back.



  6. #6
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    20567
    Downloads
    0
    Uploads
    0

    Default

    If you need the Fanuc 10,11,12 RS232 manual, P.M. me a email add.
    Al.

    CNC, Mechatronics Integration and Custom Machine Design (Skype Avail).

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  7. #7
    Registered
    Join Date
    Apr 2009
    Location
    Canada
    Posts
    674
    Downloads
    0
    Uploads
    0

    Default

    You cannot save/load pmc parameters any other way than by hand.



  8. #8
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    20567
    Downloads
    0
    Uploads
    0

    Default

    This is what I got one time from Fanuc when a 9000 option was purchased by a customer supplied on a floppy disk.
    This was a single option, I have not tried with the full 9000's.
    Al.

    Attached Thumbnails Attached Thumbnails -10_15oopt-pdf  
    CNC, Mechatronics Integration and Custom Machine Design (Skype Avail).

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  9. #9
    Registered
    Join Date
    Apr 2009
    Location
    Canada
    Posts
    674
    Downloads
    0
    Uploads
    0

    Default

    That is only for the 15A.
    I have done this hundreds of times on 10, 11,12 and 15 controls.



  10. #10
    Registered
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    349
    Downloads
    0
    Uploads
    0

    Default

    Ah yes that's written on the instructions of Fanuc 10 Fanuc 11 Memory Backup Procedures, only parameters can be punched. PMC data setting instructions here http://www.kfasllc.com/pdf/F1011_PMC_Set.pdf



  11. #11
    Registered guhl's Avatar
    Join Date
    Aug 2007
    Location
    Ukraine, Sevastopol
    Posts
    503
    Downloads
    0
    Uploads
    0

    Default

    ok I will use camera to save the PMC data
    may be to offer Fanuc to include to manual this way of saving parameters )))

    New location: Sevastopol, Crimea, Russia.


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

Follow us on

Facebook Dribbble RSS Feed