| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| Fanuc Discuss Fanuc controllers here! |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#2
 
11-24-2005, 05:09 PM
| |||
| |||
Here are the G-codes from the 6M manual. The M-codes are also listed, but may not be accurate for your machine. These are just EIA standard M-codes, and every machine builder can make up their own. G-codes: G00 Positioning G01 Linear interpolation G02 Circular interpolation CW G03 Circular interpolation CCW G04 Dwell G05 High-speed continuous cutting G07 SINE interpolation G09 Exact stop check G10 Offset value setting / work zero offset setting G17 XY plane selection G18 ZX plane selection G19 YZ plane selection G20 Inch data input G21 Metric data input G22 Stored stroke limit on G23 Stored stroke limit off G27 Zero return check G28 Automatic Zero Return G29 Return from reference point G30 Return to 2nd/3rd/4th reference point G31 Skip cutting G33 Thread cutting G40 Cutter compesation cancel G41 Cutter compensation left side G42 Cutter compensation right side G43 Tool length offset (+) G44 Tool lenght offset (-) G45 Tool offset increase G46 Tool offset decrease G47 Tool offset double increase G48 Tool offset double decrease G49 Tool lenght offset cancel G54 Work coordinate system 1 G55 Work coordingte system 2 G56 Work coordinate system 3 G57 Work coordinate system 4 G58 Work coordinate system 5 G59 Work coordinate system 6 G60 Single direction positioning G61 Exact stop check mode G62 Automatic corner override effective G64 Cutting mode G65 Custom macro simple call G66 Custom macro modal call G67 Custom macro modal call cancel G73 Peck drilling cycle G74 Counter tapping cycle G76 Fine boring cycle G80 Canned cycle cancel G81 Drilling cycle G82 Drilling cycle/counter boring G83 Peck drilling cycle G84 Tapping cycle G85 Boring cycle G86 Boring cycle G87 Back boring cycle G88 Boring cycle G89 Boring cycle G90 Absolute programming G91 Incremental programming G92 Programming of absolute zero point G94 Feed per minute G95 Feed per revolution G98 Return to initial point level in canned cycle G99 Return to R point level in canned cycle EIA standard M-codes: M00 Program Stop M01 Optional (Planned) Stop M02 End of Program M03 Spindle CW M04 Spindle CCW M05 Spindle OFF M06 Tool Change M07 Coolant No. 2 ON M08 Coolant No. 1 ON M09 Coolant OFF M10 Clamp M11 Unclamp M12 Unassigned M13 Spindle CW & Coolant ON M14 Spindle CCW & Coolant ON M15 Motion + M16 Motion - M17 Unassigned M18 Unassigned M19 Oriented Spindle Stop M20-29 Permanently Unassigned M30 End of Tape M31 Interlock Bypass M32-35 Unassigned M36-39 Permanently Unassigned M40-45 Gear Changes if Used, Otherwise Unassigned M46-47 Unassigned M48 Cancel M49 M49 Bypass Override M50-89 Unassigned M90-99 Reserved for User    |
|
| | |
| Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
| | |
Linear Mode
