check your X aixs puls coder cable and situation of inside the puls coder for dusty or dirty ,... always happen
this error just comeup when the puls coder in not working good and machine going down
check it
I wish to get some quick help to get working my CNC machine which stopped turning ON all of a sudden today
After turning ON, both of my Fanuc 0MB mill and 0TB turning machines, connected to same transformer have been showing alarms 401, 414, 424. This is happening all of a sudden as it was only about 5 days ago when both the machines were working fine.
I read forums, the manual, and read the dignostic bits 721 and 720 to find that the values were 100.
I feel that its probably the transformer which is the culprit and is giving out high voltage to my machines.
The transformer has dials reading output voltage, and 2nd phase of the three reads 500V almost when rated voltages are 415 volts per phase.
Is it that this IS THE VERY problem? Am I correct in deciphering the situation and concluding that high voltage in transformer is the issue? Or is it something to do with the machines?
Similar Threads:
- Newbie- fanuc servo alarms
- Fanuc OT Servo Alarms
- Problem- Fanuc 401 & 414 Servo Alarms
- LNC 8 servo and LDU alarms
- Need Help!- Fanuc 0t servo alarms
check your X aixs puls coder cable and situation of inside the puls coder for dusty or dirty ,... always happen
this error just comeup when the puls coder in not working good and machine going down
check it
Hi ! ajl,.... yes iam from Iran , iam not kidding , if you want to know better our why you dont comeup to Iran ? ... its very nice to see you in my home place , we are making tools ,die and every parts same as other country here we have CNC machine from 1970 up to now , right now more than 6000 machine in IRAN under working , mustly in Car manufacturer or oil industry ...
this is very short brief ,... if you wanna more try to accept my invitation , but dont forget 2 things ,...first dont believe to Media ! second , forget the politics we are brother in the same world with just One GOD ! ... have nice time my brother .
F.Sharifi
F.Sharifi,
I must say that I am quite impressed with your answer. I am not usually one to side with the Arabs but you make 2 very good points.
We may have our difference's but you said two very wise things. #1 DONT TRUST THE MEDIA...
#2 SAME WORLD WITH JUST ONE GOD....AMEN TO THAT BROTHER....
Good day
Jon Thee
Yes I know what you mean about the media. I think it would be awsome to visit the middle east my wife and I have been talking about going to Italy, I have family in Sicily. Anyhow do you have any pics? Your shop, home etc.
A.J.L.
Hi !
please send your private Email because its not possible to send more pics via CNC zon , also we are not ARAB ! IRAN is Persian poeple , we are working and living with USA people many time , iam sure we had good memo from each other .... I thinks its ok , right now our goverment doing such complicate decision but is teh same for all the countries ... every things that decided by Mr. President is OK for all USA people ?.. iam sure not !same as us ... anyhow we are Techno people and very far from politics ... its better
So what happend with alarms? I have the same alarm 444 !
Sent from my iPad using Tapatalk - now Free
Haha nice picture
Enviado desde mi GT-I9300 usando Tapatalk
My Servo motor amplifier model is A06B 6079 H103
Enviado desde mi GT-I9300 usando Tapatalk
Ok i will check tomorrow
Enviado desde mi GT-I9300 usando Tapatalk
Some peopple says me check the AC reactor
Enviado desde mi GT-I9300 usando Tapatalk
Look this pict my connection its like this. Before PSM have a AC reactor. Some peopple says check the contactor and reactor
Enviado desde mi GT-I9300 usando Tapatalk
But what i need to do if the voltage is down 280VDC????
Enviado desde mi GT-I9300 usando Tapatalk
if low voltage in circuits before PSM, it has to show it, but as you see all your drives after PSM are connected in parallel, therefore low voltage must be on all drives, not only on 4th