Need Help! Incorrect voltages and temperature on Fagor 8055m


Results 1 to 5 of 5

Thread: Incorrect voltages and temperature on Fagor 8055m

  1. #1
    Member
    Join Date
    Apr 2015
    Posts
    170
    Downloads
    0
    Uploads
    0

    Default Incorrect voltages and temperature on Fagor 8055m

    Hi everyone, I know this is a long shot but it is worth an ask. I foolishly bought a faulty Fagor 8055m controller thinking I could maybe repair it but so far it has been a case of chasing rainbows. After the test routine at start up there is the usual warning red line on the screen saying that the supply voltages are all wrong and it is overheating. Going to the diagnostic page confirms this. The supply voltages check out OK. When the axis board is removed the problem does not appear and everything is fine. The previous owner had taken this to a Fagor dealer who tested it and declared the CPU board faulty and because of the age it was not possible to supply a replacement. I can't work out what actually measures the voltage and temperature and disconnecting the +15v supply appears to have no effect on the readings in the diagnostics page, it is as if there is nothing actually measuring the voltage and the system is somehow guessing them. I have replaced various suspect chips including the CPU's to no avail. So the questions are has anyone encountered this before and does anyone know what chip would actually be capable of measuring the voltages. I have checked the voltage stabiliser chip (ad588jq) which is the only chip that I can see that actually receives all the voltages seems to work these are expensive to replace and I can't be certain it is faulty, and now I have run out of ideas and enthusiasm, any advice would be much appreciated. Thanks Dave

    Similar Threads:


  2. #2
    Member
    Join Date
    Mar 2008
    Location
    Argentina
    Posts
    169
    Downloads
    0
    Uploads
    0

    Default

    [QUOTE=Bdrangdo;2057812]Hi everyone, I know this is a long shot but it is worth an ask. I foolishly bought a faulty Fagor 8055m controller thinking I could maybe repair it but so far it has been a case of chasing rainbows. After the test routine at start up there is the usual warning red line on the screen saying that the supply voltages are all wrong and it is overheating. Going to the diagnostic page confirms this. The supply voltages check out OK. When the axis board is removed the problem does not appear and everything is fine. The previous owner had taken this to a Fagor dealer who tested it and declared the CPU board faulty and because of the age it was not possible to supply a replacement. I can't work out what actually measures the voltage and temperature and disconnecting the +15v supply appears to have no effect on the readings in the diagnostics page, it is as if there is nothing actually measuring the voltage and the system is somehow guessing them. I have replaced various suspect chips including the CPU's to no avail. So the questions are has anyone encountered this before and does anyone know what chip would actually be capable of measuring the voltages. I have checked the voltage stabiliser chip (ad588jq) which is the only chip that I can see that actually receives all the voltages seems to work these are expensive to replace and I can't be certain it is faulty, and now I have run out of ideas and enthusiasm, any advice would be much appreciated. Thanks Dave[/QUOTE

    Can you solve it?



  3. #3
    Member
    Join Date
    Apr 2015
    Posts
    170
    Downloads
    0
    Uploads
    0

    Default Re: Incorrect voltages and temperature on Fagor 8055m

    No I have not solved it as yet. I have replaced the ADC ic's and the octal transmit/receive ic's (74245) and various others but it is still the same. I still have the control but gave up on it long ago.Cheers Dave



  4. #4
    Member
    Join Date
    Mar 2008
    Location
    Argentina
    Posts
    169
    Downloads
    0
    Uploads
    0

    Default Re: Incorrect voltages and temperature on Fagor 8055m

    Oh so sorry to hear that do you have the cnc with keyboard and screen?



  5. #5
    Member
    Join Date
    Apr 2015
    Posts
    170
    Downloads
    0
    Uploads
    0

    Default Re: Incorrect voltages and temperature on Fagor 8055m

    Quote Originally Posted by kcho View Post
    Oh so sorry to hear that do you have the cnc with keyboard and screen?
    It turned out to be a faulty axis board,it's fine now. Dave



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Incorrect voltages and temperature on Fagor 8055m

Incorrect voltages and temperature on Fagor 8055m