error 368 X AXIS : SERIAL DATA ERROR (INT)


Results 1 to 6 of 6

Thread: error 368 X AXIS : SERIAL DATA ERROR (INT)

  1. #1
    Registered
    Join Date
    Nov 2007
    Location
    Thailand
    Posts
    328
    Downloads
    0
    Uploads
    0

    Default error 368 X AXIS : SERIAL DATA ERROR (INT)

    Hi All,

    Hoping that someone can help.

    I have a FADAL 3016FX, Fanuc 0i control.

    I have error 368 X AXIS : SERIAL DATA ERROR (INT)

    I also had 364 X AXIS : SOFT PHASE ALARM (INT)

    The plastic articulated track that retains the wires running under the table and to the motor on the right side of the table was somewhat damaged and some wires cut, so I took steps to repair and rejoin the wires, and also replaced the track.

    This has worked for a while, but now I have the same problems again. But now I just have error 368 X AXIS : SERIAL DATA ERROR (INT)

    What I'd really like to know is where those wire go to in the cabinet, so that I can check continuance between the cabinet and the motor to see if there's any other breaks in the cable that I missed, as I've had moments where the machine fired up and worked fine, but only for a couple of minutes.

    If so I'll probably just replace the whole cable.

    Any and all help is much appreciated.

    Regards,

    Matt.

    Similar Threads:


  2. #2
    Registered
    Join Date
    Jan 2005
    Location
    United States
    Posts
    45
    Downloads
    0
    Uploads
    0

    Default

    Cables go directly to the control, they enter the cabinet under the control on the right side. The cable getting damaged is a common issue on the FX machines, poor cable trac design and lack of maintainence contribute to the problem. You would be best to replace the cable, and remove covers to clean it out at least once a month.



  3. #3
    Registered
    Join Date
    Nov 2007
    Location
    Thailand
    Posts
    328
    Downloads
    0
    Uploads
    0

    Default

    Thanks for your reply.

    I managed to repair the cable for now, but must order a new one just in case.

    I found some of the cable track locally here in Thailand, so that's as good as it gets now.

    The machine is running fine now and it's a good job too as we have a few parts that need to be finished this week and they will be.



  4. #4
    Registered
    Join Date
    Jun 2015
    Location
    México
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: error 368 X AXIS : SERIAL DATA ERROR (INT)

    Quote Originally Posted by mattpatt View Post
    Hi All,

    Hoping that someone can help.

    I have a FADAL 3016FX, Fanuc 0i control.

    I have error 368 X AXIS : SERIAL DATA ERROR (INT)

    I also had 364 X AXIS : SOFT PHASE ALARM (INT)

    The plastic articulated track that retains the wires running under the table and to the motor on the right side of the table was somewhat damaged and some wires cut, so I took steps to repair and rejoin the wires, and also replaced the track.

    This has worked for a while, but now I have the same problems again. But now I just have error 368 X AXIS : SERIAL DATA ERROR (INT)

    What I'd really like to know is where those wire go to in the cabinet, so that I can check continuance between the cabinet and the motor to see if there's any other breaks in the cable that I missed, as I've had moments where the machine fired up and worked fine, but only for a couple of minutes.

    If so I'll probably just replace the whole cable.

    Any and all help is much appreciated.

    Regards,

    Matt.




    This is Cesar Saldivar from México


    We had this problem in a Chiron Machine in the Axis B


    We found a broken wire in the pins of conector of the encoder and the conector of the driver B


    we fixed the broken wires


    After that, the alarm was delete


    we are going to buy a new cable


    Best Regards



  5. #5
    Registered
    Join Date
    Nov 2007
    Location
    Thailand
    Posts
    328
    Downloads
    0
    Uploads
    0

    Default Re: error 368 X AXIS : SERIAL DATA ERROR (INT)

    Thanks.

    However, I found that replacing the Fadal with a Haas was the best thing I ever did. ;-)

    Matt.



  6. #6
    Registered
    Join Date
    Jan 2017
    Location
    Viet Nam
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: error 368 X AXIS : SERIAL DATA ERROR (INT)

    Help me!

    I had an error, need help!
    error 368 X AXIS : SERIAL DATA ERROR (INT)-zalo_636197378628883406-jpg

    Thanks!



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

error 368 X AXIS : SERIAL DATA ERROR (INT)
error 368 X AXIS : SERIAL DATA ERROR (INT)