Need Help!- spotdrill program stops for no reason?

[rob jerico]

made a simple spotdrill program below, now the spotting works fine its just when it gets to line N35 it stops, im sending this program from my desktop, you watch the screen on the machine and there is nothing after N35? it just stops after it spots X-4.6121? is this a comunications error? i tried sending a toolpath from a different part and it was a long program and it worked fine? am i doing something really stupid? thanks for any help guys.

machine is a 30-16 1994 fadalHT

O0002
%
N10 G91G28Z0
N11 G90G0G54X0.Y0.
N12 M6T4
N13 E1
G0G40G49G80
N14 S4200M3
N15 G0G43Z.6H4
N16 X12.9375Y-1.011
N17 G98G81X12.9375Y-1.011Z-.077R0.0F10.0
N18 X12.4121
N19 X10.9875
N20 X10.4621
N21 X9.0375
N22 X8.5121
N23 X7.0875
N24 X6.5621
N25 X5.1375
N26 X4.6121
N27 X3.1875
N28 X2.6621
N29 X1.2375
N30 X.7121
N31 X-.7121
N32 X-1.2375
N33 X-2.6621
N34 X-3.1875
N35 X-4.6121
N36 X-5.1375
N37 X-6.5621
N38 X-7.0875
N39 X-8.5121
N40 X-9.0375
N41 X-10.4621
N42 X-10.9875
N43 X-12.4121
N44 X-12.9375
N45 X-13.23Y.53
N46 X-12.12
N47 X-11.28
N48 X-10.17
N49 X-9.33
N50 X-8.22
N51 X-7.38
N52 X-6.27
N53 X-5.43
N54 X-4.32
N55 X-3.48
N56 X-2.37
N57 X-1.53
N58 X-.42
N59 X.42
N60 X1.53
N61 X2.37
N62 X3.48
N63 X4.32
N64 X5.43
N65 X6.27
N66 X7.38
N67 X8.22
N68 X9.33
N69 X10.17
N70 X11.28
N71 X12.12
N72 X13.23
N73 G80Z4.
G90H0Z0
M0

[Delw]

Renumber the progam you left one line number out between n13 and n14

Also make sure you have no comma in the program. this pc I have is too small so I cant see if there all periods or not.


Usually on a canned drilling cycle if your missing a line number or they are out of sequence you have problems however I always found that to to be true after the canned cycle. but it might be worth a try anyhow.
lets say your next tool has some of the same line numbers in it, it will sometimes jump to that next line number skipping the ones in the tool your running..

I scrapped a good drill chuck becuase of that mistake a while ago, drill chucks dont like to be used as endmills

[Delw]

you also left out 2 line numbers on the bottom too make sure you add those as well
and there is a % after your program number this needs to be before.
told you I was blind, I am seeing this stuff after I replied
also at the end your missing G00 numbers at the end
heres what it should look like
also you have a g54 and a E1 you only need a E1 or a G54 depending on what format your using.
not to be an ass but your program is very sloppy. I will show you how mine is
again I am not trying to be an ass

% O0002 N10 G91G28Z0 N11 G90G0G54X0.Y0. N12 M6T4 N13 E1 N13.5G0G40G49G80 N14 S4200M3 N15 G0G43Z.6H4 N16 X12.9375Y-1.011 N17 G98G81X12.9375Y-1.011Z-.077R0.0F10.0 N18 X12.4121 N19 X10.9875 N20 X10.4621 N21 X9.0375 N22 X8.5121 N23 X7.0875 N24 X6.5621 N25 X5.1375 N26 X4.6121 N27 X3.1875 N28 X2.6621 N29 X1.2375 N30 X.7121 N31 X-.7121 N32 X-1.2375 N33 X-2.6621 N34 X-3.1875 N35 X-4.6121 N36 X-5.1375 N37 X-6.5621 N38 X-7.0875 N39 X-8.5121 N40 X-9.0375 N41 X-10.4621 N42 X-10.9875 N43 X-12.4121 N44 X-12.9375 N45 X-13.23Y.53 N46 X-12.12 N47 X-11.28 N48 X-10.17 N49 X-9.33 N50 X-8.22 N51 X-7.38 N52 X-6.27 N53 X-5.43 N54 X-4.32 N55 X-3.48 N56 X-2.37 N57 X-1.53 N58 X-.42 N59 X.42 N60 X1.53 N61 X2.37 N62 X3.48 N63 X4.32 N64 X5.43 N65 X6.27 N66 X7.38 N67 X8.22 N68 X9.33 N69 X10.17 N70 X11.28 N71 X12.12 N72 X13.23 N73 G80G00Z4. N74 G90G00H0Z0 N75 M0

[Delw]

heres one for a spot drill

N99 M6 T17 ( 0.500 DIA. SPOT DRILL )
N100 G0 G17 G40 G80 G90 E11
N101 M3 M8 S8500
N102 X0.0 Y0.0
N103 G8
N104 Z0.3 H17
N105 G98 G82 Z-0.15 R+0.3 F15.0
N106 X-17.5 Y-0.3
N107 X-14.0
N108 X-10.5
N109 X-8.5
N110 X-5.0
N111 X-1.5
N112 X0.5
N113 X4.0
N114 X7.5
N115 X9.5
N116 X13.0
N117 X16.5
N118 Y-3.7
N119 X13.0
N120 X9.5
N121 X7.5
N122 X4.0
N123 X0.5
N124 X-1.5
N125 X-5.0
N126 X-8.5
N127 X-10.5
N128 X-14.0
N129 X-17.5
N130 X0.0 Y4.0
N131 G80 G40 M5 M9
N132 G9
N133 G49 Z0.0
N134 M01

[rob jerico]

your not being an ass at all, im very happy to get such fast responces, i did your changes and it does not work, im going to try your program, i will get back, thanks

ps im using format 2

[rob jerico]

so i modified your program that worked on my machine for me:
%
O0010
N99 M6 T4
N100 G0 G17 G40 G80 G90 E1
N101 M3 S3500
N102 X0.0 Y0.0
N103 G8
N104 Z.6 H4
N105 X12.9375 Y-1.011
N106 G98 G81 Z-.077 R+.05F15.0
N107 X12.4121
N108 X10.9875
N109 X10.4621
N110 X9.0375
N111 X8.5121
N112 X7.0875
N113 X6.5621
N114 X5.1375
N115 X4.6121
N116 X3.1875
N117 X2.6621
N118 X1.2375
N119 X.7121
N120 X-.7121
N121 X-1.2375
N122 X-2.6621
N123 X-3.1875
N124 X-4.6121 (IT STOPS HERE!)
N125 X-5.1375
N126 X-6.5621
N127 X-7.0875
N128 X-8.5121
N129 X-9.0375
N130 X-10.4621
N131 X-10.9875
N132 X-12.4121
N133 X-12.9375
N134 X-13.23 Y.53
N135 X-12.12
N136 X-11.28
N137 X-10.17
N138 X-9.33
N139 X-8.22
N140 X-7.38
N141 X-6.27
N142 X-5.43
N143 X-4.32
N144 X-3.48
N145 X-2.37
N146 X-1.53
N147 X-.42
N148 X.42
N149 X1.53
N150 X2.37
N151 X3.48
N152 X4.32
N153 X5.43
N154 X6.27
N155 X7.38
N156 X8.22
N157 X9.33
N158 X10.17
N159 X11.28
N160 X12.12
N161 X13.23
N162 G80 G40 M5
N163 G9.
N164 G49 Z0.
N165 M01


and it still stops at the same line! thanks again for any help

[Delw]

can you just load that program into the machine and run it form the machine
instead of dnc'ing it?

[rob jerico]

i would rather find out why its not working with dnc since i never use the control on the machine

[rob jerico]

Originally Posted by Delw you also left out 2 line numbers on the bottom too make sure you add those as well and there is a % after your program number this needs to be before. told you I was blind, I am seeing this stuff after I replied also at the end your missing G00 numbers at the end heres what it should look like also you have a g54 and a E1 you only need a E1 or a G54 depending on what format your using. not to be an ass but your program is very sloppy. I will show you how mine is again I am not trying to be an ass

ok i ran the program you modified with mine and it worked, im spotting different size holes and when i canceled the first cancycle with g80 its doing what it was doing before, its now reading the next cancycle and spotting about 5 holes then stops again. can i send anyone my full program to look at? thanks guys

[rob jerico]

im posting this program here, im off to my real job (im doing this at home), if someone could look at this it would help me out of a jam, thanks again guys

%
O0002
N99 G91G28Z0
N100 G90G0G54X0.Y0.
N101 M6T4
N102 E1
N103 .5G0G40G49G80
N104 S4200M3
N105 G0G43Z.6H4
N106 X12.9375Y-1.011
N107 G98G81X12.9375Y-1.011Z-.077R0.0F10.0
N108 X12.4121
N109 X10.9875
N110 X10.4621
N111 X9.0375
N112 X8.5121
N113 X7.0875
N114 X6.5621
N115 X5.1375
N116 X4.6121
N117 X3.1875
N118 X2.6621
N119 X1.2375
N120 X.7121
N121 X-.7121
N122 X-1.2375
N123 X-2.6621
N124 X-3.1875
N125 X-4.6121
N126 X-5.1375
N127 X-6.5621
N128 X-7.0875
N129 X-8.5121
N130 X-9.0375
N131 X-10.4621
N132 X-10.9875
N133 X-12.4121
N134 X-12.9375
N135 X-13.23Y.53
N136 X-12.12
N137 X-11.28
N138 X-10.17
N139 X-9.33
N140 X-8.22
N141 X-7.38
N142 X-6.27
N143 X-5.43
N144 X-4.32
N145 X-3.48
N146 X-2.37
N147 X-1.53
N148 X-.42
N149 X.42
N150 X1.53
N151 X2.37
N152 X3.48
N153 X4.32
N154 X5.43
N155 X6.27
N156 X7.38
N157 X8.22
N158 X9.33
N159 X10.17
N160 X11.28
N161 X12.12
N162 X13.23
N163 G80
(.261)
N164 Y.310X13.056
N165 G98G81Z-.335R-.270F8.
N166 X12.294
N167 X11.106
N168 X10.344
N169 X9.156
N170 X8.394
N171 X7.206 (works to here then just stops!)
N172 X6.444
N173 X5.256
N174 X4.494
N175 X3.306
N176 X2.544
N177 X1.356
N178 X.594
N179 X-.594
N180 X-1.356
N181 X-2.544
N182 X-3.306
N183 X-4.494
N184 X-5.256
N185 X-6.444
N186 X-7.206
N187 X-8.394
N188 X-9.156
N189 X-10.344
N190 X-11.106
N191 X-12.294
N192 X-13.056
N193 Y.195 X-12.675
N194 X-10.725
N195 X-8.775
N196 X-6.825
N197 X-4.875
N198 X-2.925
N199 X-.975
N200 X.975
N201 X2.925
N202 X4.875
N203 X6.825
N204 X8.775
N205 X10.725
N206 X12.675
N207 G80
(.188 thry-.238 cb)
N208 X12.825 Y.53
N209 G98G81Z-.335R-.270F8.
N210 X12.525
N211 X10.875
N212 X10.575
N213 X8.925
N214 X8.625
N215 X6.975
N216 X6.675
N217 X5.025
N218 X4.725
N219 X3.075
N220 X2.775
N221 X1.125
N222 X.825
N223 X-.825
N224 X-1.125
N225 X-2.775
N226 X-3.075
N227 X-4.725
N228 X-5.025
N229 X-6.675
N230 X-6.975
N231 X-8.625
N232 X-8.925
N233 X-10.575
N234 X-10.875
N235 X-12.525
N236 X-12.825
N237 G80
(.322)
N238 Y.792 X-13.049
N239 G98G81Z-.335R-.270F8.
N240 X-12.301
N241 X-11.099
N242 X-10.351
N243 X-9.149
N244 X-8.401
N245 X-7.199
N246 X-6.451
N247 X-5.249
N248 X-4.501
N249 X-3.299
N250 X-2.551
N251 X-1.349
N252 X-.601
N253 X.601
N254 X1.349
N255 X2.551
N256 X3.299
N257 X4.501
N258 X5.249
N259 X6.451
N260 X7.199
N261 X8.401
N262 X9.149
N263 X10.351
N264 X11.099
N265 X12.301
N266 X13.049
N267 G80
(.128 THRU, .278 1.105 DEEP)
N268 X12.675 Y.945
N269 G98G81Z-.335R-.270F8.
N270 X10.725
N271 X8.775
N272 X6.825
N273 X4.875
N274 X2.925
N275 X.975
N276 X-.975
N277 X-2.925
N278 X-4.875
N279 X-6.825
N280 X-8.775
N281 X-10.725
N282 X-12.675
N283 G80 G40 M5 M9
N284 G9
N285 G49 Z0.0
N286 M6 T6
(.07 DRILL)
N287 G0G40G49G80
N288 S4000M3
N289 G01Z.6H6F200.
(.07)
N290 X12.9375Y-1.011
N291 G98G73Q.030Z-.36R.03F5.0
N292 X12.4121
N293 X10.9875
N294 X10.4621
N295 X9.0375
N296 X8.5121
N297 X7.0875
N298 X6.5621
N299 X5.1375
N300 X4.6121
N301 X3.1875
N302 X2.6621
N303 X1.2375
N304 X.7121
N305 X-.7121
N306 X-1.2375
N307 X-2.6621
N308 X-3.1875
N309 X-4.6121
N310 X-5.1375
N311 X-6.5621
N312 X-7.0875
N313 X-8.5121
N314 X-9.0375
N315 X-10.4621
N316 X-10.9875
N317 X-12.4121
N318 X-12.9375
N319 X-13.23Y.53Z-.565
N320 X-12.12
N321 X-11.28
N322 X-10.17
N323 X-9.33
N324 X-8.22
N325 X-7.38
N326 X-6.27
N327 X-5.43
N328 X-4.32
N329 X-3.48
N330 X-2.37
N331 X-1.53
N332 X-.42
N333 X.42
N334 X1.53
N335 X2.37
N336 X3.48
N337 X4.32
N338 X5.43
N339 X6.27
N340 X7.38
N341 X8.22
N342 X9.33
N343 X10.17
N344 X11.28
N345 X12.12
N346 X13.23
N347 G80
N348 G91G28Z0.
N349 M6 T8
N350 M0
(.2610 DRILL)
N351 G0G40G49G80
N352 S4000M3
N353 G01Z.6H8F200.
N354 Y.310X13.056
N355 G98G83Z-1.105Q.11R-.270F8.
N356 X12.294
N357 X11.106
N358 X10.344
N359 X9.156
N360 X8.394
N361 X7.206
N362 X6.444
N363 X5.256
N364 X4.494
N365 X3.306
N366 X2.544
N367 X1.356
N368 X.594
N369 X-.594
N370 X-1.356
N371 X-2.544
N372 X-3.306
N373 X-4.494
N374 X-5.256
N375 X-6.444
N376 X-7.206
N377 X-8.394
N378 X-9.156
N379 X-10.344
N380 X-11.106
N381 X-12.294
N382 X-13.056
N383 Y195 X-12.675
N384 X-10.725
N385 X-8.775
N386 X-6.825
N387 X-4.875
N388 X-2.925
N389 X-.975
N390 X.975
N391 X2.925
N392 X4.875
N393 X6.825
N394 X8.775
N395 X10.725
N396 X12.675
N397 G80
N398 G91G28Z0.
N399 M6 T10
N400 M0
(.238 DRILL)
N401 G0G40G49G80
N402 S4000M3
N403 G01Z.6H10F200.
N404 X12.825 Y.53
N405 G98G83Q.11Z-1.110R-.270F8.
N406 X12.525
N407 X10.875
N408 X10.575
N409 X8.925
N410 X8.625
N411 X6.975
N412 X6.675
N413 X5.025
N414 X4.725
N415 X3.075
N416 X2.775
N417 X1.125
N418 X.825
N419 X-.825
N420 X-1.125
N421 X-2.775
N422 X-3.075
N423 X-4.725
N424 X-5.025
N425 X-6.675
N426 X-6.975
N427 X-8.625
N428 X-8.925
N429 X-10.575
N430 X-10.875
N431 X-12.525
N432 X-12.825
N433 G80
N434 G91G28Z0.
N435 M6 T12
N436 M0
(.322 DRILL)
N437 G0G40G49G80
N438 S4000M3
N439 G01Z.6H12F200.
N440 Y.792 X-13.049
N441 G98G83Q.11Z-1.110R-.270F8.
N442 X-12.301
N443 X-11.099
N444 X-10.351
N445 X-9.149
N446 X-8.401
N447 X-7.199
N448 X-6.451
N449 X-5.249
N450 X-4.501
N451 X-3.299
N452 X-2.551
N453 X-1.349
N454 X-.601
N455 X.601
N456 X1.349
N457 X2.551
N458 X3.299
N459 X4.501
N460 X5.249
N461 X6.451
N462 X7.199
N463 X8.401
N464 X9.149
N465 X10.351
N466 X11.099
N467 X12.301
N468 X13.049
N469 G80
N470 G91G28Z0.
N471 M6 T14
N472 M0
N473 G0G40G49G80
N474 S4000M3
N475 G01Z.6H14F200.
(.375 DRILL)
N476 X12.675 Y.945
N477 G98G73Q.1Z-.870R-.270F8.
N478 X10.725
N479 X8.775
N480 X6.825
N481 X4.875
N482 X2.925
N483 X.975
N484 X-.975
N485 X-2.925
N486 X-4.875
N487 X-6.825
N488 X-8.775
N489 X-10.725
N490 X-12.675
N491 G80
N492 G91G28Z0.
N493 M6 T16
N494 M0
(.188 DRILL)
N495 G0G40G49G80
N496 S4000M3
N497 G01Z.6H16F200.
N498 X12.825 Y.53
N499 G98G83Q.080Z-1.3R-1.05F6.
N500 X12.525
N501 X10.875
N502 X10.575
N503 X8.925
N504 X8.625
N505 X6.975
N506 X6.675
N507 X5.025
N508 X4.725
N509 X3.075
N510 X2.775
N511 X1.125
N512 X.825
N513 X-.825
N514 X-1.125
N515 X-2.775
N516 X-3.075
N517 X-4.725
N518 X-5.025
N519 X-6.675
N520 X-6.975
N521 X-8.625
N522 X-8.925
N523 X-10.575
N524 X-10.875
N525 X-12.525
N526 X-12.825
N527 G80
N528 G91G28Z0.
N529 M6 T18
N530 M0
(BLOW OUT .07 DRILL HOLES!)
(2-56 TAP)
N531 G0G40G49G80
N532 S1000M3
N533 G01Z.6H6F200.
(.07)
N534 X12.9375Y-1.011
N535 G98G84Z-.275R.13F17.850
N536 X12.4121
N537 X10.9875
N538 X10.4621
N539 X9.0375
N540 X8.5121
N541 X7.0875
N542 X6.5621
N543 X5.1375
N544 X4.6121
N545 X3.1875
N546 X2.6621
N547 X1.2375
N548 X.7121
N549 X-.7121
N550 X-1.2375
N551 X-2.6621
N552 X-3.1875
N553 X-4.6121
N554 X-5.1375
N555 X-6.5621
N556 X-7.0875
N557 X-8.5121
N558 X-9.0375
N559 X-10.4621
N560 X-10.9875
N561 X-12.4121
N562 X-12.9375
N563 X-13.23Y.53Z-.4
N564 X-12.12
N565 X-11.28
N566 X-10.17
N567 X-9.33
N568 X-8.22
N569 X-7.38
N570 X-6.27
N571 X-5.43
N572 X-4.32
N573 X-3.48
N574 X-2.37
N575 X-1.53
N576 X-.42
N577 X.42
N578 X1.53
N579 X2.37
N580 X3.48
N581 X4.32
N582 X5.43
N583 X6.27
N584 X7.38
N585 X8.22
N586 X9.33
N587 X10.17
N588 X11.28
N589 X12.12
N590 X13.23
N591 G80
N592 G91G28Z0.
N593 M6 T1
N594 M01

[Delw]

your programs really messed up, you have a few things missing.

email it to delapril@cox.net and I will fix it for you
Delw

[machinist_1]

Are you posting this or are you doing this on some sort of editer (note pad)?