Need Help!- fadal facing programming example

[chintan]

hi

i newly join compnay and making part programming with using fadal controller.
here i would like face 50*50 block
i am making program
m92 z250
G0 X30 Y0 Z5
G1 Z-1 F500
X-150
Z-2
X30
Z-3
X-150
CONTINU UP TO 30 MM(FACING UP TO 30MM)

IF I AM MAKING LIKE THIS IT WILL TAKE MORE TIME TO WRITE LINES
IF I WANT REPEAT SAME X AND Y AND Z SHOULD GO 1 MM DOWN UP TO 30 MM

MAY BE I HAVE TO USE SUB PRG FOR THIS
BUT I DONT KNOW I ABOUT SUB PRG
PLEASE ANYBODY SEND ME CORRECT FORMAT HOW TO REPAET PROGRAMME.

THANKING U

CHINTAN

[jbexplorer]

Hi Chintan,

I would use a sub like this:

%
L100
G1G91Z-1F500
G90X-150
G91Z-1
G90X30
M17
M30
G0G90
M6T1
E1X30Y0
H1Z5
G1Z0F500M8
L114
G0G90Z5M5M9
G49Z0
E0X0Y0
M2
%

JB

[JEST]

L100
Z-1 F500
X-180 /(G91 call will move from X30 to X-150)
Z-2
X180 /(X-150 to X30)
M17
M30
G0 G40 G90
/(need to call tool here)
/(need to call RPM and start it)
G0 X30 Y0 Z5
G91
L115 (CALL SUB 15 TIMES to go 30- SUB REMOVES 2 EACH LOOP)
G90 /(out of incremental- back to absolute)
G0 Z5 (BACK TO ORIGINAL Z)
/(turn off spindle/coolant)
G53 X0 Y0 Z0 (OR WHERE EVER YOU WANT TO END UP)
M02

This will only go to a depth of 25 as the start point is Z5. Each loop of the sub will remove 2 (Z-1 each way). If you need to remove 30, Z start would be 0 (top of part)

[chintan]

Originally Posted by jbexplorer Hi Chintan, I would use a sub like this: % L100 G1G91Z-1F500 G90X-150 G91Z-1 G90X30 M17 M30 G0G90 M6T1 E1X30Y0 H1Z5 G1Z0F500M8 L114 G0G90Z5M5M9 G49Z0 E0X0Y0 M2 % JB

thank you very much

[chintan]

Originally Posted by JEST L100 Z-1 F500 X-180 /(G91 call will move from X30 to X-150) Z-2 X180 /(X-150 to X30) M17 M30 G0 G40 G90 /(need to call tool here) /(need to call RPM and start it) G0 X30 Y0 Z5 G91 L115 (CALL SUB 15 TIMES to go 30- SUB REMOVES 2 EACH LOOP) G90 /(out of incremental- back to absolute) G0 Z5 (BACK TO ORIGINAL Z) /(turn off spindle/coolant) G53 X0 Y0 Z0 (OR WHERE EVER YOU WANT TO END UP) M02 This will only go to a depth of 25 as the start point is Z5. Each loop of the sub will remove 2 (Z-1 each way). If you need to remove 30, Z start would be 0 (top of part)

thank you very much