Excitech Cnc Router Purchase

[KustomKoncepts]

HOLD THE FREAKING PHONE


is this not the exact machine even the red plat behind the spindel is the samt the picture is from the same angel.


god I love the internet you cna find anything. even the xyz specs are the exact same as the excitech. HELLO


http://www.motiontek.ca/R118.html

[KustomKoncepts]

Yeah I am kinda stupid and when I am trying to figure out something especially, somthing so big and complex as figuring this what cnc to buy. I probubly think to fast and type too much if I slowed down and double checked stuff I would not have to hold the phone so much. JK like with the whole 3 phase fiasco when I do indead had 3 phase the whole time. what ever.

as far as this motion tek I think I did a searh for

on yahoo.com

3.5kw HSD spindel

this site was at the top of the list. I fell out of my chair when I saw that picture. I know that is the same thing. even when I convert th 1500mm x 3000mm it comes out to 59"x118" that is the specs of this machine. so now ho are they? are they a distributor for this machine? like some one else sad almost all machines are made in a hand full of factories and sold under diffferent names and colors. I have to admit that if these guys admit it is a SH and are about the same price. I am way more comfortable buying from a canadian company that is 5 hrs away on land than 20 hrs away in china. You have to understand that if it is the same It makes more cents to buy from a closer distibutor. I will run these guys through the grinder tomorrow and see what sticks. Later

[KustomKoncepts]

I belive this is the HSD spindel that is in question on these cutters.
Taney said it was from italy and this company is from italy and called HSD. I bet they are more knolegable on this 3phase 1 phase 208/240/250 volt amperage song and dance we are trying to figure out. I may contact tehem to and I hop that carvin marvin is reading this and getting his machine wired up. contact these guys if this is the spindel you have, maybe they can helf figure out your voltage and amperage problems. later

http://www.hsd-hitec.com/eng/cont/elettromandrini.asp

[KustomKoncepts]

more of my point here is once again the same machine without the side panels. All made somewhere sold differently.


http://cgi.benl.ebay.be/CNC-ROUTER-5...QQcmdZViewItem

[KustomKoncepts]

I know this says it is a excitech but look at the top of the page.

Shangding Fongder Imp. and Exp. co., ltd

the plot thickens I should have been a investigator. so here we go again who really makes this and where all can I buy it and get service on it?

I probubly don't matter these are all the same even the same color minus some decals and emblems. I hope I can get one through Toranto Canada but I will keep digging. the more I see this model on different sites kinda makes my more easy going that there are some of these out there.


http://fongder.en.alibaba.com/offerd...ng_router.html

[KustomKoncepts]

Dun Dun Dun even more. I can do this all night. here we see the same machine AGAIN under the maxicam logo. What the ****.


seriously everyone do a google search for

3.5kw hsd spindel

that is where I am finding all of these seriously, try it.


http://www.maxicam.com.cn/1530.asp

[greatscott]

isn't that an 1.5 HP Spindle? What good is that?

[cabnet636]

yes you can take the liquior from a horse thief. and after all you'll have is a sober horse thief. anyone met an irish traveller out of murphy villiage near agusta sc. they show up with aload of small diesel home generators, trash pumps and pressure washers. with cool logos that just about match the united power lable, tell you it was ordered and then the recepient died so instead of returning it you are going to get the deal of a lifetime. i came real close to paying abuot 6 grand for a bunch of low market goods that i could have bought at northern tool for 3 grand. man they had logos web sites warrantys invoice books and magnetic signs on the sides of thier trucks.
it was bizaare how i even got caught up in it. they left it, i said i'd consider
it fond the scam listed on net under irish travelors, called them said come pick it up, they barked rough, i said i was calling the sc attourney generals
office, (who has a task force on this in our state) they were thier in ten minutes bada bing bada boom

kustom, there is a woodworking show in atlanta in january
see http://www.thewoodworkingshows.com/
and in greensboro nc febuary
see http://www.carolinaswoodexpo.com/gso...ails.cfm?ID=94

i personally visited shop bot in durham (call and let them knoe your comming)
it was the best move i made in all of this.

i have considered buuilding ny own machine i have found all of the sources for all of the extrusions, servo motors, gantry, z axis, mach 3 controller gecko
drives. and all near me. there is a fantastic source of rack and pinon, linear bearings and trucks motor mounts in rock hill sc
see http://www.cncrouterparts.com/parts.html
see http://www.8020.net/
see www.CandCNC.com

i trully believe i could overbuild the machine i really want and probably will
eventully (i did build my own verticle panel saw way back when when it was my only way to get it financially those were some fun days)
however my main guys in the shop are all against this as they feel the learning curve will be less by purchasing and i am holding out for shop bot
yes i do have a sizable shop and a little flexibility here i do hope this is informative as just writing this is confirming my own work on this

shop bot
16000 +/- with spindle i am getting a extra air drill so 18000. 5x8 table
works for me

cabnet

[ger21]

Originally Posted by greatscott isn't that an 1.5 HP Spindle? What good is that?

3.5Kw = 4.7Hp

[ger21]

If anyone is getting rude or unwanted PM's, please forward them to me.

[cabnet636]

your gonna love this
i went to exibitor list for greensboro show and look what i found

http://www.camaster.com/portal/

and http://www.casstek.com/

and http://www.multicam.com/eng/index.html

is sold at http://www.pruittmachinery.com/
cabnet

[cabnet636]

check this i will peobably go and see these machines early next week if not then after thanksgiving

http://www.multicam.com/eng/Products/3000series.html
see video it does run
http://www.multicam.com/eng/Products/1000series.html

see private techs
http://www.reatechnologies.com/
so ok before i lose my entire saturday morning i'll move on with this

http://www.b2b-exchange.com/categori...09923289003027

and http://www.buyerzone.com/industrial/...e_bg2.html#pg7
cabnet