LinkBack URL
About LinkBacks
I can send you a map that shows the island where people who care live.:-)
Mariss
| | |
Well what can i say the most unhelpfull people i asumed that this site was to share and help people i put up a post asking for help and not one of you could be bothered to help so stuff the lot of you ill find a site were there are people that really want to help i hope you all rot in hell
Regards
I can send you a map that shows the island where people who care live.:-)
Mariss
I refuse to rot, but I might ferment a bit
I read the post and it looked pretty open ended so far as getting any meaningful assistance. Research, then buy after you have prepared yourself to run the gauntlet. Or, buy a ready made machine from someone.
First you get good, then you get fast. Then grouchiness sets in.
(Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
I think the title off your first post says it all
Quote: "oh! so very confused "
LOL
That was the whole point of my first page all i wanted was some help because the one thing i have found out is controlling stepper motors is hard and confusing for beginners and i hoped that out there was some one to help steer me in the right direction,But there was no help and to prove the point its amazing how many replies you get in minutes if a few home truths are posted
Hmm... Well, you did at least finish the post with "regards".Originally Posted by petersavage1
Would you have felt better if I had posted that I didn't have a clue about steppers. There is no onus on you to post queries here nor on people to respond; I think you need to get an attitude adjustment.
An open mind is a virtue...so long as all the common sense has not leaked out.
Savage Peter,
Your moniker and social commentary on a public board's hospitality don't add up. Which side of the fence are you on?
There are many good and bad ways to ask for help or illicit a response. A whole lot of information can be reaped by simply reading. Reading first often helps one to make a more specific request for help. Time, place (sub-forum) and whole lot of other factors influence the outcome.
And please don't forget that this a free forum, give or take from it what you will. But wishing the whole lot to join you for a barbecue is not neccessary.
Welcome aboard.
i read the post you are referring to , I've never heard of epe drivers nor do i have any working drivers that i would want to swap for some drivers that you can't get to work , so i couldn't help you , so would you have liked a reply saying sorry no info ?
it only takes the capabilities of creating a completed thought to call a company and ask for some technical help and if you can't do that then i guess your sol
may your plans to run cnc rot as much as your common sense and common courtesy has
A poet knows no boundary yet he is bound to the boundaries of ones own mind !! ........
http://microcarve.microcarve.biz/
WOW! Thats pretty harsh don't you think, you ask 1 question and the fine folks on this forum don't have the information you need so wish them all to hell, SHAME ON YOU. I am fairly new here, actually my second post but I have already learned soooo much just by reading' I try to find out the answers to my questions on my own and without bothering these guys. I know if I had a really good question anyone here that could help would do so but I will not ask simple questions that have been answered over and over without doing a little research on my own. Now I suggest you start by apologizing to these nice people then use the search function to try and find the information you seek, try calling or emailing the manufacturer of your parts for technical support or try reading a book, we know you have the internet, the answer is out there go find it don't expect these people to bring to you. It's not our fault you can't get it to work.
The only reason I didn't reply until now is, I charge per comment.
You owe me $57.95
(just playing, the first one is free)
That "Regards" thing was kinda funny... after you said rot in hell (party on)
.
Free DXF Files - myDXF.blogspot.com
Here's another,
mastercam x3 and centurion 7 ?
I guess we will have to take on more staff, next thing people will stop their support payments.
Al.
CNC, Mechatronics Integration and Custom Machine Design (Skype Avail).
“Logic will get you from A to B. Imagination will take you everywhere.”
Albert E.
Posting Permissions
| | |
