Osai A-B 8600

[karmoleed]

We have recently bought Utas ( Osai A-B 8600 Control )cnc Milling Machine with an OSAI – Allen Bradley 8600 control system. This unit when purchased by us was not working
We are kindly request help in guiding us to sort out the below mentioned problem.( We change the battery cause the one we get it in the control was totaly Empty)

When the machine is powered on the following messages are shown on the screen:

SERIES 8600 ver 3.0
DISC????
BUBBLE????
CMOS????
EPROM????

***INIT ABORTED***
I think we have to enter the Machine Parameters?
As we don’t have the maintenance manual for this Mc – could you kindly assist us as to what “inputs” have to be entered for the details mentioned above? Where in your view might the problem be ?
Are there any 8600 manuals ( service – troubleshooting – maintenance – programming ) - available –
Any guidance would be greatly appreciated & helpful.

Many Thanks in advance,

Regards

Eng. Yehia Abdou

[claucampan]

Hi,

If you didn't solve the problem yet:

it looks like your system files are lost. First of all you have to check the batteries on the cards of the controller, and change them if necessary.

then you have to reload all data. The system files you can find on the floppy disk that was supplied with the machine. You will also need a cable for transfer.

If you have problems, you can send me an PM, or an e-mail at: clau_campan@yahoo.com

[good_320]

HI I AM SHAMAS FOROM ISB PK .I HAD WORKED ON AB OSAI 8601T SERIAS CONTROL AND NOW WORKING AB OSAI 8600 CONTROL .I HAVE SOME OF DATA ABOUT THIS CONTROL AND KNOW WHERE ARE ITS SERVICE MANUL AVALABLE IF U NEED HELP THEN SEND ME EMAIL ON MY EMAIL ADDER. good_320@yahoo.com

[cris5963]

Hello everybody,
I need a help for OSAI 8600.
After initialization of the CNC /batery replacement/ , the error messages on display apears in format - FILMSx.xx
The system files and the files with error messages ara on the right place.
Any idea how to solve this problem?

Thanks in advance

[ikavakci]

hi cris5963;,
I have some problem now.
How can you solve this problem?
Because pc not connect to nc with rs232.
Is there any initializa methods?

[JORGE ARAYA]

I need help
I have a cnc osai AB 8600 v 5.2 mono us with the following problems:
srtring My4 error = 14,0,21
Error number: 6
Error number: 141

Jorge Araya

[claucampan]

Originally Posted by JORGE ARAYA I need help I have a cnc osai AB 8600 v 5.2 mono us with the following problems: srtring My4 error = 14,0,21 Error number: 6 Error number: 141 Jorge Araya

Error 141 seems to be THE POS record is missing (syntax or format error)
for error 6 Unauthorized operator name (an error in a characterization file)

My4 error?!?!

Probably you should reload the all parameters

[claucampan]

Originally Posted by cris5963 Hello everybody, I need a help for OSAI 8600. After initialization of the CNC /batery replacement/ , the error messages on display apears in format - FILMSx.xx The system files and the files with error messages ara on the right place. Any idea how to solve this problem? Thanks in advance

If you didn't solve the error display problem: check if you still have the correct fcrsys file. In this file, section *7, all the 5 types of errors are assign to a specific error message file. (films1 to edperr, films2 to edpmsg, etc...)

[JORGE ARAYA]

how can reload all the parameters again from osai 6800

thank you for responding

[claucampan]

You'll need a back up of the characterization files (AXCFIL, EDPERR, EDPMSG, FCRSYS,....ETC), a cable and a transfer program. But I'm wondering what's that

srtring My4 error = 14,0,21

. Can you please give more details about this error? When the error appear on the monitor and the exact error message.

[JORGE ARAYA]

the machine now only shows the screen:
eprom :???? ???? ???? ????
CMOS :???? ????
****init aborted ****

[claucampan]

Looks like you've lost all the data from the PLC. Usually it happens when the voltage of the batteries is low. First you have to check them and if necessary to replace the batteries, and than all to reload the files I mentioned before.

For reloading the parameters there's a procedure in OSAI manuals, I don't remember exactly in which one. Send me a PM if you need more details.