Newbie- post

[jpk1961]

Does anybody have a esprit post for a fanuc 16i-mb on kitamura bridge 8f

[dcoupar]

What version of Esprit? Can you post a sample of the code with startup, tool changes, etc. Somebody may have something close.

[jpk1961]

Thanks for the the quick responce.
I have esprit 2008.
Here is a small sample of code
Thanks jpk1961
O0000
(PROGRAM FOR Kitamura)
(SOURCE FILE NAME - PUNCH HOLDER FACE )
(PART REV PROGRAMMER )
(CREATED ON 02 - 09 - 09 AT 12:09 AM )
(======= START OF PROGRAM =======)
N10 G91 G28 Z0.
N20 G90
N30 G17 G40 G80 G49 M01
( #4 CENTERDRILL TOOL1 DIA .125 )
( DIA OFFSET D1 LEN OFFSET H1 )
N40 T1 M06
N50 G0 G90 X-9.665 Y0. S2139 M3
N60 G43 H1 Z3. M8 T31
N70 G98 G81 Z-.03 R.1 F5.4
N80 G80 G90
N90 M9
N100 M5
N110 G91 G28 Z0.
N120 M01
( 13/16 SPADE DRILL TOOL31 DIA .813 )
( DIA OFFSET D31 LEN OFFSET H31 )
N130 T31 M6
N140 G0 G90 X-11.125 Y-3.625 S798 M3
N150 G43 H31 Z3. T10 M8
N160 G98 G83 Z-2.8441 R.1 Q.1 F7.98
N170 G80 G90
N180 M9
N190 M5
N200 G91 G28 Z0.
N210 M01
( 5/16-18 TAPRH TOOL10 DIA .313 )
( DIA OFFSET D10 LEN OFFSET H10 )
N220 T10 M6
N230 G0 G90 X-12.875 Y-1.925 S213 M3
N240 G43 H10 Z3. T37 M8
N250 G98 G84 Z-.8 R.1 S213 F11.83
N260 G80 G90
N270 M9
N280 M5
N290 G91 G28 Z0.
N300 M01
( .66 CHAMFER MILL TOOL37 DIA .660 )
( DIA OFFSET D37 LEN OFFSET H37 )
N310 T37 M6
N320 G0 G90 X-11.125 Y-8.625 S2894 M3
N330 G43 H37 Z3. T1
N340 Z.1
N350 G1 Z-.08 F23.
N360 X-11.0869 Y-8.5869
N370 G3 X-11.125 Y-8.5488 I-.0381 J0.
N380 X-11.125 Y-8.5488 I0. J-.0762
N390 X-11.1631 Y-8.5869 I0. J-.0381
N400 G1 X-11.125 Y-8.625
N410 G0 Z3.
N420 M5
N430 G91 G28 Z0.
N440 M99
N450 G90 M30
%

[dcoupar]

Here's one I use for a YCM XV1020. It should be close enough to get you started. You'll have to rename it with an .asc extension. Let me know...

[jpk1961]

Thanks I will give it a try
jpk1961

[jpk1961]

dcoupar
I tried this post it did not create any code
i did change the extention.
Thanks jpk1961

[dcoupar]

Well, I don't know what to say. I just tried it again, and it did! Send me a PM with your esp file attached, and I'll take a look.

[Camorenob]

Good evening all community I am programer of CNC with EspritCAM I need the following postprocesor for EspritCAM:
ROMI lathe, model C 20V, control Mach 5,
MAZAK lathe, Model QT 18MS, Control Mazatrol T32
HASS Machining center, Model VF1, Control Hass

I would be grateful to them very much for you who could help me and if in my hands this one them to help with something they can make it know me