RFQ - Additional CNC Machined Aluminum Part

[HighCaliber]

In addition to the other RFQ listed, I would like to receive a quote on this Machined Part from T6 6061 Aluminum. I would prefer to receive quotes from only Canadian and American shops. The material would be supplied by you.

Would like to receive a quote on quantities of 10, 20, 50, 100, from T6 6061 Aluminum.

Please note that half the order would be mirrored (Right side and Left side)

RFQ End date is March 2nd. Would be looking to receive the products within 2 - 3 weeks after award date (partial order is acceptable).

Any suggestions on how the parts could be modified to improve cost-effectiveness would be greatly appreciated.

3D file available upon request.

Thank you all in Advance,

Chris
XD Engineering
sales@highcalibermotorsports.com

[mfg]

Chris,

You probably won't get many quotes here. Some of the members here are also members at mfg.com. They can easily look up your Xtreme Doors profile and see that you wrote rubber checks to some of your suppliers and never bothered to pay the rest of them before they kicked you off the site.
I would think if anyone does work for you it will have to be paid in advance.

[HighCaliber]

Originally Posted by mfg Chris, You probably won't get many quotes here. Some of the members here are also members at mfg.com. They can easily look up your Xtreme Doors profile and see that you wrote rubber checks to some of your suppliers and never bothered to pay the rest of them before they kicked you off the site. I would think if anyone does work for you it will have to be paid in advance.

We have been in contact with all of our previous suppliers regarding that situation. We had a major order placed, product was shipped, and the person disappeared. We would be paying cash upfront at time of order placement for these parts, as we have indeed learned a valuable lesson. These parts will not be purchased until previous suppliers have been reimbursed which is being done as we speak.

Thanks,

Chris

[HighCaliber]

Hello,

I would like to thank everyone who submitted a quote for this part. We have reviewed all quotes and this RFQ has been awarded to a member on this site.

Again Thank you,
Chris

[Clawsie Machine]

Originally Posted by HighCaliber Hello, I would like to thank everyone who submitted a quote for this part. We have reviewed all quotes and this RFQ has been awarded to a member on this site. Again Thank you, Chris

Thanks for NOT getting back to me? I PM'ed, emailed, AND PHONED

[HighCaliber]

Hey,

We did infact PM you back regarding your original PM, however as we stated we would not be around much as we were busy moving to a new facility. We have been having email problems so chances are that our emails going to you are not getting through to you. I apologize for that, also you never stated in any of your emails that you needed 3D files.

We have other parts that we will be needing and we would be happy to receive some quotes from you.

Thanks,
Chris

[Clawsie Machine]

Check Your Pm's

[jetski]

I just down loaded your drawing and will be looking at it tonight. Our shop rate is low. You can reach me at gsilberberg@progressive-plastics.net

[Helix60]

Look at Post #4. It's already been awarded. Not sure who to though...

Regards,
Heli

Originally Posted by jetski I just down loaded your drawing and will be looking at it tonight. Our shop rate is low. You can reach me at gsilberberg@progressive-plastics.net

[WILLwork4money]

jetski, I think this RFQ is closed, read my pasted quote down @ the bottom from Buyer!!

jetski Chip Sweeper I just down loaded your drawing and will be looking at it tonight. Our shop rate is low. You can reach me at gsilberberg@progressive-plastics.net

Old 03-06-2007, 01:45 PM
HighCaliber
Chip Sweeper

Join Date: Feb 2007 Location: Canada Posts: 8 I would like to thank everyone who submitted a quote for this part. We have reviewed all quotes and this RFQ has been awarded to a member on this site. Again Thank you, Chris