Dynomotion/Kflop/Kanalog - Page 3


Page 3 of 43 FirstFirst 12345613 ... LastLast
Threads 41 to 60 of 849

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. MPGSmooth.c

    Started by eman5oh‎, 10-25-2015 11:16 AM
    code, counts_per_mm, movement, mpgsmooth.c, pendant
    • Replies: 11
    • Views: 942
    11-09-2017, 03:37 PM Go to last post
  2. Build Thread- CNC 6040 - upgrade to KFLOP

    Started by CNCtronic‎, 11-07-2017 02:58 PM
    • Replies: 2
    • Views: 252
    11-07-2017, 03:15 PM Go to last post
  3. My Fadal 4020 Kflop Retrofit

    Started by mmurray70‎, 10-31-2017 11:21 PM
    • Replies: 11
    • Views: 448
    11-03-2017, 09:51 PM Go to last post
  4. KFLOP KANALOG FADAL

    Started by COlger‎, 10-31-2017 11:14 AM
    coolant, fadal, kflop, mach4, software
    • Replies: 3
    • Views: 234
    11-01-2017, 06:26 PM Go to last post
  5. Newbie- A lot of questions...

    Started by CNCtronic‎, 10-30-2017 07:41 PM
    lot, mode, motors, questions, reset
    • Replies: 1
    • Views: 206
    10-30-2017, 11:28 PM Go to last post
  6. Need Help!- Looking for C code info...

    Started by CNCtronic‎, 10-26-2017 07:14 PM
    • Replies: 3
    • Views: 207
    10-27-2017, 03:44 PM Go to last post
  7. Need Help!- Read current value of Kanalog DAC

    Started by durundal‎, 10-25-2017 06:26 PM
    current, dac, kanalog, read, similar
    • Replies: 1
    • Views: 131
    10-25-2017, 06:51 PM Go to last post
  8. Need Help!- Are the Kanalog ADC's 12 volt tolerant?

    Started by todmorg‎, 10-25-2017 12:38 AM
    inputs, kanalog, on/off, reading, volt
    • Replies: 1
    • Views: 139
    10-25-2017, 01:11 AM Go to last post
  9. Question Newbie- KFLOP and Midi

    Started by vrsculptor‎, 10-22-2017 04:59 PM
    • Replies: 2
    • Views: 184
    10-22-2017, 10:37 PM Go to last post
  10. Need Help!- Machine Halts at a specific kind of G-Codes.

    Started by amitkumar171‎, 10-17-2017 09:49 AM
    code, g-codes, halts, machine, stops
    • Replies: 5
    • Views: 253
    10-22-2017, 12:37 AM Go to last post
    • Replies: 3
    • Views: 941
    10-17-2017, 07:53 PM Go to last post
  11. Need Help!- Automatic Tool Change C Code

    Started by slimneill‎, 04-01-2017 12:27 PM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 1,500
    10-16-2017, 07:28 PM Go to last post
  12. GamePad questions

    Started by netboss‎, 10-12-2017 04:27 PM
    controller, gamepad, kmotioncnc, leads, xbox
    • Replies: 1
    • Views: 216
    10-14-2017, 03:40 PM Go to last post
  13. Need Help!- KmotionCNC Screen Editor Capability Questions

    Started by slimneill‎, 10-13-2017 01:50 PM
    change, kmotioncnc, screen, status, tool
    • Replies: 2
    • Views: 207
    10-13-2017, 07:45 PM Go to last post
  14. xhc for KMotionCNC

    Started by frate‎, 03-23-2015 05:18 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 1,781
    10-12-2017, 08:09 PM Go to last post
  15. Need help: Runaway machine after INIT

    Started by randyrhine‎, 10-11-2017 05:15 PM
    • Replies: 2
    • Views: 156
    10-11-2017, 05:54 PM Go to last post
  16. Need Help!- What have I done now??? Threads per inch changed on me.

    Started by netboss‎, 10-06-2017 03:05 PM
    changed, checked, inch, point, threading
    • Replies: 4
    • Views: 212
    10-09-2017, 01:11 AM Go to last post
  17. Do loop

    Started by Gregore‎, 10-01-2017 12:03 PM
    hundred, loop, move, simple, stop
    • Replies: 5
    • Views: 273
    10-09-2017, 12:15 AM Go to last post
  18. Need Help!- How to Connect External Buttons in Kflop or Kanalog

    Started by amitkumar171‎, 10-03-2017 03:49 AM
    estop, external buttons, feed hold, kanalog, kflop
    • Replies: 3
    • Views: 229
    10-03-2017, 01:46 PM Go to last post

Page 3 of 43 FirstFirst 12345613 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 17 users browsing this forum. (0 members & 17 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands