Dynomotion/Kflop/Kanalog - Page 27


Page 27 of 57 FirstFirst ... 172425262728293037 ... LastLast
Threads 521 to 540 of 1126

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Snap Amp... Supply reverse polarity

    Started by spank‎, 01-31-2015 08:48 PM
    input, polarity, power, supply, took, try
    • Replies: 5
    • Views: 780
    07-15-2016, 03:00 AM Go to last post
  2. Waterjet Axis Tuning Help :)

    Started by purple_jeep‎, 05-26-2016 11:43 PM
    2 Pages
    1 2
    • Replies: 20
    • Views: 1,314
    07-12-2016, 10:02 PM Go to last post
  3. Need Help!- Proper Startup/Shutdown Procedure for Kflop

    Started by MadTooler‎, 07-11-2016 01:14 AM
    5volt, powering, proper, software, supply
    • Replies: 1
    • Views: 583
    07-11-2016, 02:55 PM Go to last post
  4. Lightbulb Solved Chinese (Lichaun) Servo Using RS232

    Started by Suumas‎, 07-04-2016 02:58 PM
    • Replies: 1
    • Views: 620
    07-05-2016, 12:15 PM Go to last post
  5. Build Thread- Dynomotion used with Technics SSt-Eclipse servo drives??

    Started by ckphillips‎, 06-27-2016 09:22 AM
    cont, drives, dynomotion, sst-eclipse, technics
    • Replies: 3
    • Views: 502
    06-27-2016, 01:23 PM Go to last post
    • Replies: 11
    • Views: 1,161
    06-25-2016, 12:54 PM Go to last post
  6. Problem- Motion Control Question

    Started by JoeKumanchik‎, 06-14-2016 12:57 PM
    axis, disable, enabled, kflop, motion
    • Replies: 3
    • Views: 670
    06-15-2016, 09:45 AM Go to last post
    • Replies: 6
    • Views: 1,228
    06-14-2016, 04:02 PM Go to last post
  7. feedhold blocking move in either direction

    Started by Den095‎, 06-09-2016 05:18 PM
    axis, feedhold, limit, limits, positive
    • Replies: 2
    • Views: 723
    06-10-2016, 02:44 AM Go to last post
  8. Need Help!- Stepper Motor Tuning

    Started by bcmaint‎, 06-06-2016 03:17 PM
    • Replies: 12
    • Views: 1,883
    06-09-2016, 08:48 AM Go to last post
  9. Question Help! 8 Axis? I can't even get to 6!

    Started by kash4kev‎, 06-08-2016 11:24 AM
    board, inputs, kanalog, kflop, motors
    • Replies: 1
    • Views: 836
    06-08-2016, 07:29 PM Go to last post
  10. Kflop 5v plugged in wrong.

    Started by Layman94‎, 06-06-2016 04:16 AM
    computer, connected, kanalog, kflop, plugged
    • Replies: 2
    • Views: 700
    06-07-2016, 10:03 AM Go to last post
  11. Need Help!- Replacing Mach3, USB SmoothStepper with a KFlop and more.

    Started by FelixPQ‎, 05-27-2016 05:15 PM
    accuracy, cnc, machine, precision, repeatability
    • Replies: 9
    • Views: 1,311
    06-06-2016, 09:59 AM Go to last post
    • Replies: 1
    • Views: 510
    06-04-2016, 02:16 PM Go to last post
  12. Question Need Help!- KFlop to Super PID PWM contorl

    Started by JoeKumanchik‎, 05-15-2016 08:59 PM
    board, cnc, kflop, pwm, superpid
    • Replies: 6
    • Views: 1,101
    05-31-2016, 01:44 PM Go to last post
  13. Problem- DAC != 0 after following error

    Started by cyberjack‎, 05-27-2016 08:58 PM
    code, dac, detect, error, set
    • Replies: 3
    • Views: 1,113
    05-31-2016, 06:31 AM Go to last post
  14. Help with Accurate Servo Tuning

    Started by purple_jeep‎, 10-30-2015 12:17 AM
    • Replies: 15
    • Views: 2,453
    05-27-2016, 12:43 PM Go to last post
  15. New Konnect question

    Started by Eddard_Stark‎, 05-20-2016 11:13 AM
    • Replies: 4
    • Views: 695
    05-26-2016, 09:06 AM Go to last post
  16. Need Help!- Adding a KAnalog to a KFlop

    Started by kash4kev‎, 05-09-2016 02:53 PM
    • Replies: 7
    • Views: 2,338
    05-25-2016, 12:56 AM Go to last post

Page 27 of 57 FirstFirst ... 172425262728293037 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 12 users browsing this forum. (0 members & 12 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands