Dynomotion/Kflop/Kanalog - Page 12


Page 12 of 57 FirstFirst ... 2910111213141522 ... LastLast
Threads 221 to 240 of 1126

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Updated drawing

    Started by mirocha‎, 11-19-2018 10:35 AM
    • Replies: 1
    • Views: 902
    11-19-2018, 12:11 PM Go to last post
  2. Closed loop feedback to glass linear encoders

    Started by men8ifr‎, 10-24-2018 01:18 PM
    • Replies: 12
    • Views: 3,743
    11-18-2018, 04:07 AM Go to last post
  3. Need Help!- How to get and set offsets for U and V axes

    Started by amitkumar171‎, 11-12-2018 11:56 PM
    • Replies: 1
    • Views: 759
    11-16-2018, 12:31 AM Go to last post
  4. Kflop dont boot up

    Started by mk00‎, 11-14-2018 12:28 AM
    burning, constantly, diodes, kflop, reason
    • Replies: 2
    • Views: 661
    11-14-2018, 12:52 AM Go to last post
  5. ouput signal

    Started by dmoglianesi‎, 09-27-2018 01:54 PM
    0/360, axes, degrees, format, rotational
    • Replies: 13
    • Views: 1,494
    11-04-2018, 12:22 PM Go to last post
  6. help urgent

    Started by dmoglianesi‎, 10-16-2018 05:14 PM
    dalmazio, moglianesi, send, test, week
    • Replies: 10
    • Views: 713
    10-25-2018, 04:22 AM Go to last post
  7. Dual loop intput interconnect

    Started by funding33‎, 10-22-2018 05:14 PM
    • Replies: 1
    • Views: 510
    10-23-2018, 12:48 PM Go to last post
  8. How to abort MoveExp()

    Started by funding33‎, 10-19-2018 04:43 PM
    abort, ch2-output, ch2-output;, disturbances, moveexp
    • Replies: 1
    • Views: 415
    10-19-2018, 05:15 PM Go to last post
  9. Need Help!- Control commands for the microcontroller.

    Started by zaxtone‎, 08-31-2018 01:00 PM
    atmega128, commands, control, microcontroller, output
    • Replies: 10
    • Views: 1,151
    10-15-2018, 06:34 PM Go to last post
  10. Need Help!- Regarding encoder input to kflop

    Started by amitkumar171‎, 09-14-2018 06:47 AM
    • Replies: 12
    • Views: 1,429
    10-11-2018, 11:28 AM Go to last post
  11. Lightbulb kflop for robot

    Started by huynguyen93‎, 10-05-2018 12:03 AM
    • Replies: 0
    • Views: 1,220
    10-05-2018, 12:03 AM Go to last post
  12. Question Questions for TomK re. Linux and Kanalog

    Started by Toneski‎, 10-02-2018 07:39 AM
    linux, questions, tom, version, wine linux
    • Replies: 4
    • Views: 758
    10-03-2018, 11:36 AM Go to last post
  13. Screen editor --- Unhandled exception

    Started by todmorg‎, 09-30-2018 10:38 PM
    • Replies: 5
    • Views: 657
    10-01-2018, 12:14 PM Go to last post
    • Replies: 1
    • Views: 698
    09-30-2018, 12:42 PM Go to last post
  14. Viewing console from KmotionCNC

    Started by mmurray70‎, 08-30-2018 10:42 AM
    2 Pages
    1 2
    • Replies: 20
    • Views: 2,025
    09-28-2018, 11:09 AM Go to last post
  15. Need Help!- How to use all 8 Axes in Kflop Board Connected with Kanalog Board

    Started by amitkumar171‎, 09-07-2017 10:00 AM
    • Replies: 12
    • Views: 1,681
    09-24-2018, 01:57 AM Go to last post
  16. Need Help!- Instruction on Knozz wiring and setup

    Started by amitkumar171‎, 10-18-2017 03:15 AM
    2 Pages
    1 2
    • Replies: 37
    • Views: 4,796
    09-20-2018, 12:24 PM Go to last post
  17. Flexicam ATC router retrofit with Kflop/Kanalog

    Started by xyz-cnc‎, 09-06-2018 09:06 AM
    2 Pages
    1 2
    • Replies: 33
    • Views: 2,562
    09-18-2018, 04:16 PM Go to last post
  18. Problem- KmotionCNC DRO flashing yellow/blue while running gcode

    Started by MadTooler‎, 09-17-2018 06:03 PM
    dro, kmotioncnc, normal, router, running
    • Replies: 2
    • Views: 934
    09-17-2018, 06:43 PM Go to last post
  19. Watchdog FET

    Started by itme‎, 09-13-2018 09:57 AM
    • Replies: 0
    • Views: 451
    09-13-2018, 09:57 AM Go to last post

Page 12 of 57 FirstFirst ... 2910111213141522 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 13 users browsing this forum. (1 members & 12 guests)

  1. IngSushi

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands