Dynomotion/Kflop/Kanalog


Page 1 of 57 12341151 ... LastLast
Threads 1 to 20 of 1126

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Auto Tool Zeroing

    Started by -Sliver-‎, 09-30-2016 05:16 PM
    automatically, height, plate, sets, z-axis
    • Replies: 9
    • Views: 1,708
    10-03-2016, 03:56 PM Go to last post
  2. Need Help!- Z axis falls

    Started by 09FLHX‎, 08-22-2014 11:14 AM
    amplifier, axis, backlash, cnc, cnc., down, dro, dynomotion, experience, idle, ini, kflop, kstep, machine, motor, open, power, power supply, problem, running, spindle, stepper, stepper motor, supply, turning, z axis
    • Replies: 1
    • Views: 864
    08-22-2014, 02:04 PM Go to last post
  3. Mr.

    Started by 2805‎, 01-06-2019 12:01 PM
    card, good, kflop
    • Replies: 0
    • Views: 873
    01-06-2019, 12:01 PM Go to last post
  4. Some Questions

    Started by 691175002‎, 03-27-2012 11:00 PM
    • Replies: 7
    • Views: 2,132
    04-01-2012, 11:23 AM Go to last post
  5. Need Help!- printer port on hp compaq to connect 4 axis driver

    Started by aalekh‎, 12-28-2014 10:12 PM
    axis, driver, port, printer, win
    • Replies: 1
    • Views: 414
    12-29-2014, 02:28 PM Go to last post
  6. Smile A few questions : jerk, offsets, hotkeys .

    Started by Abarmot‎, 02-14-2013 08:17 AM
    • Replies: 7
    • Views: 2,064
    03-13-2013, 11:51 AM Go to last post
  7. Tom K lost in mail kana log board

    Started by Abundance‎, 06-08-2015 12:27 PM
    .425-3192327, arrange, board, shipped, tom
    • Replies: 0
    • Views: 584
    06-08-2015, 12:27 PM Go to last post
  8. Unhappy Need Help!- Huanyang inverter dead after set Pd004 to 01 by mistake!

    Started by adi7791‎, 11-21-2017 04:26 PM
    fuse, inverter, set, smoke, tiime
    • Replies: 7
    • Views: 1,824
    11-22-2017, 10:27 AM Go to last post
  9. Kinematics in Visual Studio

    Started by AKG1904‎, 10-14-2022 02:22 AM
    dynomotion, kanalog, kflop, kinematics, visual studio
    • Replies: 1
    • Views: 1,105
    10-19-2022, 02:47 PM Go to last post
  10. KFLOP with G540 No Motor Movement

    Started by akmolski‎, 06-28-2021 03:38 PM
    g540, kflop, motors, posts, signal
    • Replies: 3
    • Views: 563
    06-29-2021, 03:11 AM Go to last post
  11. KFLOP in CL Step Mode - Output Instability

    Started by akmolski‎, 06-29-2021 05:16 PM
    2 Pages
    1 2
    • Replies: 28
    • Views: 1,712
    07-16-2021, 10:08 PM Go to last post
  12. Kanalog to stepper driver wiring

    Started by albertoro‎, 07-12-2014 11:11 AM
    • Replies: 0
    • Views: 553
    07-12-2014, 11:11 AM Go to last post
  13. Linear encoders + kanalog. Wiring question

    Started by Alex101‎, 08-27-2015 11:56 AM
    • Replies: 15
    • Views: 1,334
    08-28-2015, 02:26 AM Go to last post
  14. Need Help!- How to connect external board to kflop?

    Started by Alex101‎, 03-04-2016 01:41 PM
    • Replies: 8
    • Views: 2,074
    01-14-2017, 04:34 PM Go to last post
  15. Question Need Help!- Programming KFlop in C. Tiny C compiler. Development tools.

    Started by Alexa Flame‎, 04-18-2014 05:51 AM
    already, another, available, everyone, next, plus, regards, say
    • Replies: 7
    • Views: 1,645
    03-05-2016, 04:01 PM Go to last post
  16. Need Help!- Geo Correction

    Started by Alexa Flame‎, 11-04-2014 06:54 AM
    • Replies: 7
    • Views: 1,180
    11-05-2014, 08:03 PM Go to last post
  17. KMotionCNC

    Started by alexandr_st‎, 01-15-2013 10:45 PM
    • Replies: 8
    • Views: 2,091
    01-17-2013, 01:11 AM Go to last post
  18. Newbie- KMotionCNC, how change axis channel number?

    Started by alexxp‎, 01-07-2017 05:26 PM
    axis, channel, kmotioncnc, running, spindle
    • Replies: 2
    • Views: 571
    01-07-2017, 09:37 PM Go to last post

Page 1 of 57 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 35 users browsing this forum. (0 members & 35 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands