Dynomotion/Kflop/Kanalog


Page 1 of 44 123411 ... LastLast
Threads 1 to 20 of 865

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. New Machine Build- Newbie: Questions about initialization c file

    Started by slwoss‎, Today 10:05 AM
    break, file, gcode, initialization, load
    • Replies: 4
    • Views: 81
    Today, 02:16 PM Go to last post
  2. Build Thread- Tree325 Retrofit Started

    Started by PeterTheWolf‎, 09-24-2017 08:10 PM
    16 Pages
    1 2 3 4 5 ... 16
    • Replies: 184
    • Views: 7,556
    Today, 02:26 AM Go to last post
  3. Kflop thread/C program question

    Started by curtiskelowna‎, Today 01:16 AM
    • Replies: 5
    • Views: 100
    Today, 02:22 AM Go to last post
  4. KFLOP Not Recognized by USB....

    Started by Fish4Fun‎, 09-17-2012 10:19 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 2,227
    Today, 01:29 AM Go to last post
  5. Fill in the Blanks Gcode Dynomotion

    Started by Need TECH Help!‎, 02-19-2018 09:36 PM
    blanks, fill, gcode, make, mill
    • Replies: 8
    • Views: 190
    02-20-2018, 09:11 PM Go to last post
  6. Need Help!- How to wire Active High proximity sensor to kflop JP7

    Started by amitkumar171‎, 01-01-2018 02:22 AM
    2 Pages
    1 2
    • Replies: 17
    • Views: 594
    02-19-2018, 12:55 PM Go to last post
  7. Need Help!- USB cable length

    Started by geast1967‎, 02-16-2018 03:57 PM
    15m, cable, isolated, long, usb
    • Replies: 4
    • Views: 137
    02-16-2018, 06:43 PM Go to last post
  8. Steppers using KFlop/Kanalog via JP4 and pin 15/16

    Started by oligocyte‎, 02-14-2018 05:51 PM
    • Replies: 6
    • Views: 156
    02-15-2018, 07:13 PM Go to last post
  9. My Fadal 4020 Kflop Retrofit

    Started by mmurray70‎, 10-31-2017 11:21 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 608
    02-12-2018, 08:22 AM Go to last post
  10. Spindle stops during a job

    Started by rbickle‎, 02-06-2018 07:32 PM
    #define, fro, speed, spindle, variable
    • Replies: 7
    • Views: 228
    02-08-2018, 02:53 PM Go to last post
  11. Tool offset trouble

    Started by rbickle‎, 02-05-2018 08:04 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 367
    02-08-2018, 02:04 PM Go to last post
    • Replies: 1
    • Views: 137
    02-05-2018, 02:46 PM Go to last post
  12. Build Thread- MAHO 600E

    Started by swat cat‎, 10-30-2017 05:34 AM
    2 Pages
    1 2
    • Replies: 22
    • Views: 741
    02-03-2018, 11:21 AM Go to last post
  13. Question Newbie- Modbus/rs232

    Started by Niyaz‎, 01-29-2018 02:45 AM
    • Replies: 4
    • Views: 169
    01-30-2018, 02:33 AM Go to last post
  14. Need Help!- Mach3, Kflop, RPM and index signal (convert from a Parellel World)

    Started by Mark_990‎, 01-27-2018 05:17 AM
    kflop, mach3, rpm, speed, spindle
    • Replies: 3
    • Views: 148
    01-29-2018, 02:35 PM Go to last post
  15. New Machine Build- Machine shaking on small holes

    Started by mirocha‎, 01-27-2018 06:45 PM
    • Replies: 8
    • Views: 299
    01-29-2018, 02:26 PM Go to last post
  16. Homing update and new question

    Started by netboss‎, 09-03-2017 12:01 PM
    cycle, duty, home, offset, wave
    • Replies: 7
    • Views: 545
    01-27-2018, 10:08 PM Go to last post
  17. Problem with K-flop after shpindle starting

    Started by Dobro‎, 01-27-2018 03:37 AM
    • Replies: 3
    • Views: 141
    01-27-2018, 09:58 PM Go to last post
  18. KMotionCNC Screen Editor

    Started by oligocyte‎, 01-26-2018 02:36 PM
    editor, find, kmotioncnc, obvious, screen
    • Replies: 1
    • Views: 123
    01-26-2018, 03:19 PM Go to last post
  19. Ini file for inch

    Started by mirocha‎, 01-24-2018 10:10 PM
    file, find, joe, save
    • Replies: 1
    • Views: 205
    01-25-2018, 01:01 AM Go to last post

Page 1 of 44 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 43 users browsing this forum. (5 members & 38 guests)

  1. TomKerekes,
  2. slwoss,
  3. curtiskelowna,
  4. m_c,
  5. mmurray70

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands