Dynomotion/Kflop/Kanalog


Page 1 of 44 123411 ... LastLast
Threads 1 to 20 of 865

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Fill in the Blanks Gcode Dynomotion

    Started by Need TECH Help!‎, 02-19-2018 09:36 PM
    blanks, fill, gcode, make, mill
    • Replies: 9
    • Views: 219
    Today, 12:50 PM Go to last post
  2. Need Help!- .NET + Labview problem

    Started by copperwr‎, 11-03-2016 01:51 PM
    .net, .n~, clr, directory, labview
    • Replies: 10
    • Views: 436
    Yesterday, 07:44 PM Go to last post
  3. New Machine Build- Newbie: Questions about initialization c file

    Started by slwoss‎, Yesterday 10:05 AM
    break, file, gcode, initialization, load
    • Replies: 5
    • Views: 152
    Yesterday, 02:36 PM Go to last post
  4. Build Thread- Tree325 Retrofit Started

    Started by PeterTheWolf‎, 09-24-2017 08:10 PM
    16 Pages
    1 2 3 4 5 ... 16
    • Replies: 184
    • Views: 7,588
    Yesterday, 02:26 AM Go to last post
  5. Kflop thread/C program question

    Started by curtiskelowna‎, Yesterday 01:16 AM
    • Replies: 5
    • Views: 122
    Yesterday, 02:22 AM Go to last post
  6. KFLOP Not Recognized by USB....

    Started by Fish4Fun‎, 09-17-2012 10:19 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 2,246
    Yesterday, 01:29 AM Go to last post
  7. Need Help!- How to wire Active High proximity sensor to kflop JP7

    Started by amitkumar171‎, 01-01-2018 02:22 AM
    2 Pages
    1 2
    • Replies: 17
    • Views: 598
    02-19-2018, 12:55 PM Go to last post
  8. Need Help!- USB cable length

    Started by geast1967‎, 02-16-2018 03:57 PM
    15m, cable, isolated, long, usb
    • Replies: 4
    • Views: 140
    02-16-2018, 06:43 PM Go to last post
  9. Steppers using KFlop/Kanalog via JP4 and pin 15/16

    Started by oligocyte‎, 02-14-2018 05:51 PM
    • Replies: 6
    • Views: 161
    02-15-2018, 07:13 PM Go to last post
  10. My Fadal 4020 Kflop Retrofit

    Started by mmurray70‎, 10-31-2017 11:21 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 609
    02-12-2018, 08:22 AM Go to last post
  11. Spindle stops during a job

    Started by rbickle‎, 02-06-2018 07:32 PM
    #define, fro, speed, spindle, variable
    • Replies: 7
    • Views: 228
    02-08-2018, 02:53 PM Go to last post
  12. Tool offset trouble

    Started by rbickle‎, 02-05-2018 08:04 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 371
    02-08-2018, 02:04 PM Go to last post
    • Replies: 1
    • Views: 137
    02-05-2018, 02:46 PM Go to last post
  13. Build Thread- MAHO 600E

    Started by swat cat‎, 10-30-2017 05:34 AM
    2 Pages
    1 2
    • Replies: 22
    • Views: 748
    02-03-2018, 11:21 AM Go to last post
  14. Question Newbie- Modbus/rs232

    Started by Niyaz‎, 01-29-2018 02:45 AM
    • Replies: 4
    • Views: 170
    01-30-2018, 02:33 AM Go to last post
  15. Need Help!- Mach3, Kflop, RPM and index signal (convert from a Parellel World)

    Started by Mark_990‎, 01-27-2018 05:17 AM
    kflop, mach3, rpm, speed, spindle
    • Replies: 3
    • Views: 149
    01-29-2018, 02:35 PM Go to last post
  16. New Machine Build- Machine shaking on small holes

    Started by mirocha‎, 01-27-2018 06:45 PM
    • Replies: 8
    • Views: 302
    01-29-2018, 02:26 PM Go to last post
  17. Homing update and new question

    Started by netboss‎, 09-03-2017 12:01 PM
    cycle, duty, home, offset, wave
    • Replies: 7
    • Views: 549
    01-27-2018, 10:08 PM Go to last post
  18. Problem with K-flop after shpindle starting

    Started by Dobro‎, 01-27-2018 03:37 AM
    • Replies: 3
    • Views: 147
    01-27-2018, 09:58 PM Go to last post
  19. KMotionCNC Screen Editor

    Started by oligocyte‎, 01-26-2018 02:36 PM
    editor, find, kmotioncnc, obvious, screen
    • Replies: 1
    • Views: 127
    01-26-2018, 03:19 PM Go to last post

Page 1 of 44 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 13 users browsing this forum. (2 members & 11 guests)

  1. PeterTheWolf,
  2. sean7457

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands