Dynomotion/Kflop/Kanalog


Page 1 of 44 123411 ... LastLast
Threads 1 to 20 of 863

Forum: Dynomotion/Kflop/Kanalog

Discuss Dynomotion/Kflop/Kanalog here!

  1. Fill in the Blanks Gcode Dynomotion

    Started by Need TECH Help!‎, Yesterday 09:36 PM
    blanks, fill, gcode, make, mill
    • Replies: 8
    • Views: 163
    Today, 09:11 PM Go to last post
  2. Build Thread- Tree325 Retrofit Started

    Started by PeterTheWolf‎, 09-24-2017 08:10 PM
    16 Pages
    1 2 3 4 5 ... 16
    • Replies: 181
    • Views: 7,432
    Today, 08:59 PM Go to last post
  3. KFLOP Not Recognized by USB....

    Started by Fish4Fun‎, 09-17-2012 10:19 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 2,154
    Today, 01:34 PM Go to last post
  4. Need Help!- How to wire Active High proximity sensor to kflop JP7

    Started by amitkumar171‎, 01-01-2018 02:22 AM
    2 Pages
    1 2
    • Replies: 17
    • Views: 588
    Yesterday, 12:55 PM Go to last post
  5. Need Help!- USB cable length

    Started by geast1967‎, 02-16-2018 03:57 PM
    15m, cable, isolated, long, usb
    • Replies: 4
    • Views: 132
    02-16-2018, 06:43 PM Go to last post
  6. Steppers using KFlop/Kanalog via JP4 and pin 15/16

    Started by oligocyte‎, 02-14-2018 05:51 PM
    • Replies: 6
    • Views: 152
    02-15-2018, 07:13 PM Go to last post
  7. My Fadal 4020 Kflop Retrofit

    Started by mmurray70‎, 10-31-2017 11:21 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 604
    02-12-2018, 08:22 AM Go to last post
  8. Spindle stops during a job

    Started by rbickle‎, 02-06-2018 07:32 PM
    #define, fro, speed, spindle, variable
    • Replies: 7
    • Views: 222
    02-08-2018, 02:53 PM Go to last post
  9. Tool offset trouble

    Started by rbickle‎, 02-05-2018 08:04 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 359
    02-08-2018, 02:04 PM Go to last post
    • Replies: 1
    • Views: 131
    02-05-2018, 02:46 PM Go to last post
  10. Build Thread- MAHO 600E

    Started by swat cat‎, 10-30-2017 05:34 AM
    2 Pages
    1 2
    • Replies: 22
    • Views: 738
    02-03-2018, 11:21 AM Go to last post
  11. Question Newbie- Modbus/rs232

    Started by Niyaz‎, 01-29-2018 02:45 AM
    • Replies: 4
    • Views: 164
    01-30-2018, 02:33 AM Go to last post
  12. Need Help!- Mach3, Kflop, RPM and index signal (convert from a Parellel World)

    Started by Mark_990‎, 01-27-2018 05:17 AM
    kflop, mach3, rpm, speed, spindle
    • Replies: 3
    • Views: 146
    01-29-2018, 02:35 PM Go to last post
  13. New Machine Build- Machine shaking on small holes

    Started by mirocha‎, 01-27-2018 06:45 PM
    • Replies: 8
    • Views: 290
    01-29-2018, 02:26 PM Go to last post
  14. Homing update and new question

    Started by netboss‎, 09-03-2017 12:01 PM
    cycle, duty, home, offset, wave
    • Replies: 7
    • Views: 541
    01-27-2018, 10:08 PM Go to last post
  15. Problem with K-flop after shpindle starting

    Started by Dobro‎, 01-27-2018 03:37 AM
    • Replies: 3
    • Views: 135
    01-27-2018, 09:58 PM Go to last post
  16. KMotionCNC Screen Editor

    Started by oligocyte‎, 01-26-2018 02:36 PM
    editor, find, kmotioncnc, obvious, screen
    • Replies: 1
    • Views: 116
    01-26-2018, 03:19 PM Go to last post
  17. Ini file for inch

    Started by mirocha‎, 01-24-2018 10:10 PM
    file, find, joe, save
    • Replies: 1
    • Views: 200
    01-25-2018, 01:01 AM Go to last post
  18. Pop Up Reminder

    Started by Need TECH Help!‎, 01-04-2018 03:25 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 373
    01-22-2018, 03:14 PM Go to last post
  19. Need Help!- Kflop boot voltage problem.

    Started by todmorg‎, 01-20-2018 07:36 PM
    boot, jumper, kflop, voltage, volts
    • Replies: 1
    • Views: 139
    01-21-2018, 04:09 PM Go to last post

Page 1 of 44 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 24 users browsing this forum. (2 members & 22 guests)

  1. Need TECH Help!,
  2. PeterTheWolf

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands