Dmm Dyn4 pmdx126 ess control build - Page 3

Page 3 of 3 FirstFirst 123
Results 25 to 32 of 32

Thread: Dmm Dyn4 pmdx126 ess control build

  1. #25
    Registered
    Join Date
    Feb 2016
    Location
    United States
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Dmm Dyn4 pmdx126 ess control build

    • According to the website they are
    • Single/Three-Phase 110~240VAC ± 10% 50/60Hz input




  2. #26
    Gold Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    7058
    Downloads
    0
    Uploads
    0

    Default Re: Dmm Dyn4 pmdx126 ess control build

    Quote Originally Posted by RootbeerFLHX View Post
    • According to the website they are
    • Single/Three-Phase 110~240VAC ± 10% 50/60Hz input
    That is correct for the Dyna4 Drives

    Mactec54


  3. #27
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    United States
    Posts
    30552
    Downloads
    0
    Uploads
    0

    Default Re: Dmm Dyn4 pmdx126 ess control build

    So they can be run from 120V single phase?

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  4. #28
    Registered
    Join Date
    Feb 2016
    Location
    United States
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Dmm Dyn4 pmdx126 ess control build

    Quote Originally Posted by ger21 View Post
    So they can be run from 120V single phase?
    Yes.



  5. #29
    Registered
    Join Date
    Jul 2010
    Location
    USA
    Posts
    34
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by RootbeerFLHX View Post
    Yes.
    Not sure for 120v. I had wired mine direct and measured the draw then added 10% and used a D curve which allows a 10 times spike for the rectifier and capacitors to charge.



  6. #30
    Registered
    Join Date
    Feb 2016
    Location
    United States
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by LtDan View Post
    Not sure for 120v. I had wired mine direct and measured the draw then added 10% and used a D curve which allows a 10 times spike for the rectifier and capacitors to charge.
    Ok. When you measured your draw were you running the servo on the machine, or just sitting at idle?



  7. #31
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    United States
    Posts
    30552
    Downloads
    0
    Uploads
    0

    Default Re: Dmm Dyn4 pmdx126 ess control build

    I found a good deal on EMI filters, if you need any.
    (1pcs) NEW!! SCHAFFNER - FN610-3-06 - POWER LINE FILTER USPP FN610306 | eBay

    He charges $5 shipping for as many as you want. When you purchase, it charges $5 each, but he refunds the extra shipping.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  8. #32
    Registered
    Join Date
    Jul 2010
    Location
    USA
    Posts
    34
    Downloads
    0
    Uploads
    0

    Default

    I locked the shaft with an old pulley and a big pipe wrench lol don't try this unless your certain you can hold it. I saw 7.4 amp on 248v then the drive errored. I am using 32amp breaker on 240v for 3 750w drives.
    Fyi I used the dmm drive software to command the motor in test movement mode. You can just do the math and get your answer.
    It is probably gonna be close to double.



Page 3 of 3 FirstFirst 123

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Dmm Dyn4 pmdx126 ess control build
Dmm Dyn4 pmdx126 ess control build