Need Help! morbidelli 504 tria 7500 - CNCzone.com-The Largest Machinist Community on the net!

rprman1 · #1 07-30-2009, 01:44 PM

I can't load programs into the control via floppy. Can anyone help. There are no alarms.

stoned · #2 10-09-2009, 11:55 AM

I have expiriensed the same problem once, the floppy drive was broken. Try whit a new drive.

sns · #3 08-31-2010, 08:57 AM

Need urgent help for a Tria 7500 controller. Back-up batteri is gone dead, so the controller lost all data. Need help for the procedure to reinstall data. Got disk whith all data on (original) but need help step for step.

stoned · #4 08-31-2010, 10:33 AM

Hey SNS.
I got the procedure for both 503 and 504 whit a Tria 7500 controller.
Just send your mail address and i send it to you.

best Stoned.

sns · #5 09-01-2010, 10:02 AM

Hi Stoned
Thank you.
My email is s.naursgaard@gmail.com
Hope it's works
best SNS

lllhuy · #6 10-07-2010, 10:12 AM

Originally Posted by stoned

Hey SNS.
I got the procedure for both 503 and 504 whit a Tria 7500 controller.
Just send your mail address and i send it to you.

best Stoned.

Hi Stoned
pls send me too. I have a same problem.

lllhuy

stoned · #7 10-07-2010, 10:26 AM

Just send me a valid mail adress, and i post the procedure to you.
Stoned.

lllhuy · #8 10-07-2010, 10:31 AM

Originally Posted by stoned

Just send me a valid mail adress, and i post the procedure to you.
Stoned.

Hi Stoned

My email is lllhuy@yahoo.com

Thanks
lllhuy

CADMAN-LV · #9 10-07-2010, 03:36 PM

Stoned

I would very much appreciate you sending me the proceedures as I to have a dead battery and need to reload.

e-mail CADMAN-LV@hotmail.com

Thank You

CADMAN-LV

Baldo · #10 10-29-2010, 10:15 AM

Hello every one.... is somebody able to help me?
I have problems with A504K.. when loading the files of the PLC
when this in the installation process
it doesn't finish.... and it puts an error..... "Register not connected Y131"

In other times I had reinstalled those all the parameters
without any problem....

e-mail uvaltierra@oakwest.com

jjjr40 · #11 10-30-2010, 07:44 AM

same problem here, I think you have to know how to boot from the floppy disk
does anybody have the instructions on reloading the plc, it just says input/output error

email -admin@highlane.org

papadapoli · #12 01-02-2011, 03:06 PM

Hi Stone,
I have the same problem, can you send me the procedure,
I have a morbidelli Author 504
and my email is
jorgeboga@hotmail.com

THANKS!!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
tria 4000	JLcnc	General CNC (Mill and Lathe) Control Software (NC)	8	05-16-2012 09:02 PM
Tria 7500 for Morbidelli Author 503	stoned	General CNC (Mill and Lathe) Control Software (NC)	11	02-25-2012 12:38 PM
Need Help!- morbidelli author 504	msahin2012	Commercial CNC Wood Routers	0	05-19-2009 07:06 AM
morbidelli MAGNETIC dc servo	michaeldriscoll	Servo Motors and Drives	2	01-05-2008 02:28 PM
Aspan 6.2 and Tria 4000	datacon1	Commercial CNC Wood Routers	0	05-16-2007 12:03 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)