Doosan VMC fanuc - no rapid or feed when spindle off

Results 1 to 16 of 16

Thread: Doosan VMC fanuc - no rapid or feed when spindle off

  1. #1
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Default Doosan VMC fanuc - no rapid or feed when spindle off

    Hello everyone. Does anyone know what can cause the machine to not move in rapid or feed mode when the spindle is not turning? We checked parameter 3708 SAR bit and it is off, we checked stroke limits and safety zones and they are not used. The machine homes properly after power up (uses dogs). Tool changer works properly. We checked all Parameters and Keep Relays and compared them to the original printouts kept in the control behind the machine and all are good. Nothing out of the ordinary. It's also in Feed Per Minute, not Feed Per Rev so that isn't a factor either and wouldn't cause non-rapid moves with the spindle off anyway.

    Time to pull my hair out.

    Fanuc iO control.
    3 axis VMC

    Thanks

    Similar Threads:


  2. #2
    Member dhardt's Avatar
    Join Date
    Feb 2013
    Location
    United States
    Posts
    788
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Is it in "DRY RUN" mode?

    No longer with Doosan Machine Tools America
    darrylhardt@gmail.com


  3. #3
    Member dcoupar's Avatar
    Join Date
    Mar 2003
    Location
    USA
    Posts
    2932
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    I thought there was an M-code to enable movement with the spindle stopped?



  4. #4
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Quote Originally Posted by dhardt View Post
    Is it in "DRY RUN" mode?
    Dry Run is off. Also when Cycle start is pressed the machine moves a small amount for about a half second then stops but the Cycle Start lamp is still on. Diagnostics show it is still in Cycle Run. Pressing the Feed Hold lights the Feed Hold button then pressing Cycle Start again moves the machine for about a half second then repeat over and over.



  5. #5
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Hey dhardt, you may be on to something. I just now turned on Dry Run and the machine moved normally but in the override federate as it should and it finished the program block without stopping but with Dry Run off the axis' will stop after a half second or so. hmmm



  6. #6
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    After speaking with a Doosan service tech, he said it's quite possibly a board issue. in 30 years of Doosan maintenance, he has never heard of our problem.



  7. #7
    Member
    Join Date
    Nov 2007
    Location
    Canada and Nothern ireland
    Posts
    351
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Most DMV -VMC Doosan's or Daewoo's need an M-code to allow you to preform this and should be in your option list or M-Code list with the machine



  8. #8
    Member
    Join Date
    Apr 2011
    Location
    USA
    Posts
    841
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Sounds like ypou have an issues with the Rapid Override signals. Dry Run goes as fast as what is set in parameter 1410. Not sure how your override signals are being handled. Check the ladder for G14.0 and G14.1 to see if they are both on. When both of these are on you are at 0% override. If they are both off then you at 100%



  9. #9
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Quote Originally Posted by drdos View Post
    Sounds like ypou have an issues with the Rapid Override signals. Dry Run goes as fast as what is set in parameter 1410. Not sure how your override signals are being handled. Check the ladder for G14.0 and G14.1 to see if they are both on. When both of these are on you are at 0% override. If they are both off then you at 100%
    G14.0 and G14.1 are 0 (not triggered at 100%) and they switch on and off depending on where my Rapid Override is set (0%, 25%, 50%, 100%) so that seems to be working correctly with the spindle on or off.

    G12.2, G12.5 & G12.6 are triggered when the spindle is not running and stay triggered and the machine stops. When the spindle is on, those same bits are triggered for a split second and return to zero and the machine runs normally.

    The test program I am running is G0 G91 X5.0 with and without the spindle on.



  10. #10

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    have you tried m184 as this allows the movement of the axis without the spindle turning m185 reverts back to spindle rotation required when axis is feeding ....

    this does not apply to rapids however, but just a thought as its a free test you can try and something extra you can rule out.



  11. #11
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Quote Originally Posted by gavintwopies View Post
    have you tried m184 as this allows the movement of the axis without the spindle turning m185 reverts back to spindle rotation required when axis is feeding ....

    this does not apply to rapids however, but just a thought as its a free test you can try and something extra you can rule out.

    Gavin,
    Our Doosans do not accept the M184 or M185.

    Rich



  12. #12
    Member Ksorensen69's Avatar
    Join Date
    May 2010
    Location
    USA
    Posts
    5
    Downloads
    8
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Quote Originally Posted by Zbuilder View Post
    Gavin,
    Our Doosans do not accept the M184 or M185.

    Rich
    Try using G98 inches per minute vs G99 inches per revolution.

    Sent from my Moto G (5S) Plus using Tapatalk



  13. #13
    Member Ksorensen69's Avatar
    Join Date
    May 2010
    Location
    USA
    Posts
    5
    Downloads
    8
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Quote Originally Posted by Ksorensen69 View Post
    Try using G98 inches per minute vs G99 inches per revolution.

    Sent from my Moto G (5S) Plus using Tapatalk
    Oops didn't see that you already tried that.


    Sent from my Moto G (5S) Plus using Tapatalk



  14. #14
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Ok I found out when M65 is commanded, the machine moves normally but M30 or RESET disables it. Sooooo, what the heck is M65/M66 on a Doosan Mecatec ???



  15. #15
    Registered
    Join Date
    Apr 2007
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0

    Unhappy Re: Doosan VMC fanuc - no rapid or feed when spindle off

    Machine defaults to G98 and is/was during all these trials. Thanks anyway.
    sigh, I'm thinking something on the main board went south.



  16. #16
    Member dhardt's Avatar
    Join Date
    Feb 2013
    Location
    United States
    Posts
    788
    Downloads
    0
    Uploads
    0

    Default Re: Doosan VMC fanuc - no rapid or feed when spindle off

    What is the machine's serial number? (found on the placard, located near the main power switch)
    What is the Electrical Hardware version? (found on the placard, located near the main power switch)

    What is the ladder version?
    Press the <SYSTEM> hard key
    Press the <PMC> softkey (depending on Fanuc model)
    Press the <PMCPRM> or <PMCCONFIG> (depending on Fanuc model)
    Press the <TITLE> softkey
    There is a field: PROGRAM DRAWING NUMBER (it is in the middle of the page)
    It contains a LONG alphanumeric sequence, separated by a comma or colon...and then another alphanumeric sequence
    I need the WHOLE code...everything in that field.


    From this information, I can see why the machine does anything and everything related to IO

    Edited due to slight deviation from normal: Mecatec information might not be in the requested locations.

    No longer with Doosan Machine Tools America
    darrylhardt@gmail.com


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Doosan VMC fanuc - no rapid or feed when spindle off

Doosan VMC fanuc - no rapid or feed when spindle off