Need Help! Help with Novusun NVEM USB control card - Page 2


Page 2 of 2 FirstFirst 12
Results 21 to 32 of 32

Thread: Help with Novusun NVEM USB control card

  1. #21
    Registered
    Join Date
    Jul 2009
    Location
    USA
    Posts
    12
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Quote Originally Posted by ky1duck View Post
    So what stepper motor drivers being used with nvum?.
    I am using HY-DIV268N-5A, with minor modifications. All three axis are working well with two NEMA 23 and one NEMA 34 motor. I have run them fast and slow. Not seeing any dropout.
    I am using a 25Volt power supply to the NVUM, and 36 volts to the drivers. The 36 volt supply is analog with a large transformer. I also have a 100 UF 63V cap at the top of each driver on the power terminals. With the distributed capacitance not getting much noise. I will try to get an oscilloscope on it this weekend.
    tholling55



  2. #22
    Registered
    Join Date
    Jul 2009
    Location
    USA
    Posts
    12
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    I thought about the issue you documented and wanted to note that there are several versions of the NVUM USB driver out. One is labeled 100KHZ. That driver does not work reliably in my system either. It does something odd to the motor timing. I tried it, then switched back to the original driver and everything seems reliable again. Which driver are you using?



  3. #23
    Registered
    Join Date
    Aug 2015
    Posts
    9
    Downloads
    0
    Uploads
    0

    Default

    Sorry for the delay, been busy at work. I have 3 different versions Of the driver, I am using k eight now. And I did find out that it was just wouldn't work with my old m5r2 drivers. I ordered a few tb6600 and it works good with them. On a down note I blew the motor control board in my x2, waiting for my new and whole lot better one to show up now. Will be doing a full review video on 2 different motor control board I found. A good one and a cheap Chinese one.



  4. #24
    Member
    Join Date
    Mar 2018
    Location
    Mexico
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Hello Everyone,
    Does anyone have the PROMA THC 150 working with the NVEM USB 200khz?
    I have them both properly connected and configured in the THC inputs on Mach3, also I checked the THC option in the "Port and Pins". So, when I set the Proma on test mode I even see the THC leds going On/Off on the "Diagnostics" screen. However the Z axis won't move up or down, even though I enable the THC botton on the main screen.
    I've done a quick research and I've found that the THC inputs are not supported using USB breakout boards, but I just wonder if there is a new driver version for this board that somehow support these THC inputs. Anyone?


    Attached Thumbnails Attached Thumbnails Help with Novusun NVEM USB control card-s-l500-jpg  


  5. #25
    Registered
    Join Date
    Nov 2017
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Quote Originally Posted by morg769 View Post
    Hello Socramor

    I will tell you I sent mine back. The A-axis would not step right and after a few lines of code it would tell me there was an USB ERROR and stop. I am going back to my old breakout board and a UC400ETH Motion Controller. But here is a rough wiring diagram of what I had. Hope it helps and if you need any other questions let me know. Rod
    Help with Novusun NVEM USB control card-nvem-wiring-diagram-jpg
    Hi, thanks for sharing the detail which is more useful. Since im building a CNC machine as a first time Hobby work, im literally confused on the wiring, im planning to make two different type of 6 axis machine operation 1) Orientable-Spindle machine 2) Orientable-table Machine. based on the manual i have done teh wiring detail for all the component, Still im unable to conclude the wiring completion for VFD / Limit switch /E-Stop / MPG. and need the list of power supply on the same.

    here with im attaching the available circuit diagram, request you to cross verify and guide me for the further wiring, if there is nay correction required, plz let me know.

    6 axis NVUM control board.pdf

    https://drive.google.com/file/d/1slU...xN9zuPfswfRd0t

    Kindly do teh needful



  6. #26
    Registered
    Join Date
    Nov 2017
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Quote Originally Posted by JUGETEK-Rony View Post
    I brought a copy one at low price : Novusun NVEM USB control card
    It works well.
    Hi, thanks for sharing the detail which is more useful. Since im building a CNC machine as a first time Hobby work, im literally confused on the wiring, im planning to make two different type of 6 axis machine operation 1) Orientable-Spindle machine 2) Orientable-table Machine. based on the manual i have done teh wiring detail for all the component, Still im unable to conclude the wiring completion for VFD / Limit switch /E-Stop / MPG. and need the list of power supply on the same.

    here with im attaching the available circuit diagram, request you to cross verify and guide me for the further wiring, if there is nay correction required, plz let me know.

    6 axis NVUM control board.pdf

    https://drive.google.com/file/d/1slU...xN9zuPfswfRd0t

    Kindly do teh needful



  7. #27
    Registered
    Join Date
    Nov 2017
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Quote Originally Posted by morg769 View Post
    Hello Socramor

    I will tell you I sent mine back. The A-axis would not step right and after a few lines of code it would tell me there was an USB ERROR and stop. I am going back to my old breakout board and a UC400ETH Motion Controller. But here is a rough wiring diagram of what I had. Hope it helps and if you need any other questions let me know. Rod
    Help with Novusun NVEM USB control card-nvem-wiring-diagram-jpg

    Dear Friend

    Since this is my first time machine build as my hobby work , Im totally confused and im unable to move further for the wiring connectivity keep struggling for months together.
    Circuit details are mentioned below:
    https://drive.google.com/file/d/1HUm...ew?usp=sharing
    https://drive.google.com/file/d/1qoT...ew?usp=sharing

    Considering on the above circuit details , Kindly give the answer / guide /solution for each of the below question:
    1) Im planning to operate the control board to make both the functional machine 1) orientable- Spindle machine 2) orientable - Table Machine { both the METHODOLOGY detail i have mentioned in the attached drawing } , is it possible operate in this method? Or needs to change any mentioned axis.

    2) OPTION-1 as a Orientable -Spindle Machine = X- Axis / Y- Axis / Z- Axis / A-Axis (as a 4th axis) / B-Axis (as a 5th axis ) and W-Axis (as a 6th axis) basically where spindle alone will take action of move (up & down) ( front & Back), in the position of spindle body dependence on the effect of A-Axis & B- Axis . in this case can i take a control terminal from C Axis? or there are some other options available ? or its not possible? For your better understanding im attaching a machine detail with considered axis.

    3) OPTION-2 as Orientable-Table Machine = X- Axis / Y- Axis / Z- Axis / B-Axis (as a 4th axis) / C-Axis (as a 5th axis ) . is it correct?

    4) For OUTX connection , What is the capacity of relay needs to use for this complete setup? plz provide me the product link its possible.

    5) What is the capacity of POTENTIOMETER needs to connect for this complete setup? plz provide me the product link its possible.

    6) MPG wiring connections are correct? ( MPG product link -
    https://www.aliexpress.com/item/NVMP...311.0.0.nfVxqg
    )

    7) VFD wire connection is correct? if any thing needs to add or if some thing is wrong plz guide me how to connect.(simple hand sketch also fine) (product link -
    https://www.aliexpress.com/item/Free...608.0.0.moeUKz
    )

    8) Im planning to make a physical HOMING & LIMIT SWITCH for the all 6 Axis ( X / Y / Z / A / B / C ) , in this case in manual there is one number of limit switch where shown, but im having 12 numbers , plz guide me how to connect? (simple hand sketch also fine)

    9) If im using PROXIMEY limit switch means, how i can connect for all 6 Axis ?

    10) In SPINDLE S-AXIS - ( INDEX ) Is this terminals not required to connect anywhere? If this terminals needs to have connection ? where to connect?

    11) In OUT PORT ( OUT-4 , OUT-6 , OUT-8 , OUT-10 , OUT-5 , OUT-7 , OUT-9 ) which and are all the terminals not required to connect anywhere? which and are all the terminals needs to have connection ? where to connect?

    12) In MPG ( 10X , E-STOP , B-IN , Z-IN , X-IN , 100X , 1X , C-IN , A-IN , Y-IN , GND ) which and are all the terminals not required to connect anywhere? which and are all the terminals needs to have connection ? where to connect?

    13) In 12-32Vin = shall we go a head with 36V power supply ? If you can able to give teh product link will be much helpful.

    14) Communication external interface terminal ( white plug with 4 connecting lead) where to connect? what its purpose? in manual also no detail available.

    15) In INPUT PORT - ( INP-3 , INP-4 , INP-5 , INP-6 , INP-7 , 12V , INP-8 , INP-9 , INP-10 , INP-11 , INP-12 , GND 1 ) which and are all the terminals not required to connect anywhere? which and are all the terminals needs to have connection ? where to connect?

    16) Kindly give the list of power supply unit for the complete set

    17) Can we use this Control board for the plasma cutting machine too?

    Request you to help me out to complete this project.

    Attached Files Attached Files


  8. #28
    Registered
    Join Date
    Feb 2009
    Location
    Venezuela
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Hi my friend could you please send to me USB cable inclusive
    Program & manual by email.



  9. #29
    Registered
    Join Date
    Feb 2009
    Location
    Venezuela
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Hi asuratman i have thos card, but i don´t know how to use , could you please help me...



  10. #30
    *Registered User* cncfoamshaper's Avatar
    Join Date
    Oct 2018
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    I'm running the Version 2 of this Controller (see my video)
    Unless the controller is bad it sounds like a settings issue in the MACH3 setup.
    Follow the ports and pins setup from the Novsusun manual and you'll be ok. I have the A axis slaved to the y axis with the motor reversed. Works fine.



  11. #31
    Member syntronik's Avatar
    Join Date
    Jul 2013
    Location
    Parma
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Problems with VSun R2 6 axis

    Anything is OK, i have only problems, the axis, do not go, example Z must be increas when go up, + direction, and - down direction, it's not possible, to reverse the
    signal direction, i set anything, also to invert the motor by hardware, when i push Z + in the jog it go up, but count down, and is not possible to change,
    what i can do??
    Thanks
    Maurizio Crescini
    www.syntcncsrl.com



  12. #32
    Registered DigitalDream's Avatar
    Join Date
    Oct 2018
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: Help with Novusun NVEM USB control card

    Go to Menu-Config-Port&Pins -- Motor Output on Mach3 sofware,you can change the Z axis direction.

    Huan Chen
    Digital Dream
    Digital Dream Automation Technology Co., Ltd.Digital Dream



Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Help with Novusun NVEM USB control card

Help with Novusun NVEM USB control card