Controller & Computer Solutions


Page 1 of 56 1234 11 51 ... LastLast
Threads 1 to 20 of 1101

Forum: Controller & Computer Solutions

Discuss computers and setups for cnc controllers.

  1. Seeking advice on converting machine to either Mach or LinuxCNC

    Started by BMcCaskill‎, 12-30-2016 01:14 PM
    3 Pages
    1 2 3
    card, engineering, glentek, machine, software
    • Replies: 30
    • Views: 845
    Yesterday, 03:40 PM Go to last post
  2. Problem- NUM 750 - view/edit of PLC

    Started by animisiewaz‎, 02-27-2017 05:33 PM
    control, machine, plc, software, view
    • Replies: 0
    • Views: 61
    02-27-2017, 05:33 PM Go to last post
  3. Smile Problem- Problem regarding choosing hardware

    Started by ankur27‎, 02-26-2017 06:49 AM
    • Replies: 3
    • Views: 168
    02-27-2017, 12:40 AM Go to last post
  4. New Machine Build- Need Some Guidance

    Started by upsala36‎, 02-24-2017 02:14 PM
    ethercat, gcode, hardware, interpreters, linuxcnc
    • Replies: 0
    • Views: 110
    02-24-2017, 02:14 PM Go to last post
    • Replies: 1
    • Views: 500
    02-22-2017, 03:59 PM Go to last post
  5. Need Help!- Rambo 5v cnc milling machine

    Started by protopaja‎, 03-20-2014 08:31 AM
    #00, rambo, then
    • Replies: 1
    • Views: 537
    02-20-2017, 08:06 AM Go to last post
  6. Heidenhain 530 Kinematic adjustement problem

    Started by barefr‎, 02-15-2017 07:06 PM
    cut, cycle, kinematic, peace
    • Replies: 0
    • Views: 142
    02-15-2017, 07:06 PM Go to last post
  7. New Control Cabinet for UCCNC or EdingCNC

    Started by jon8949‎, 02-02-2017 06:32 PM
    • Replies: 10
    • Views: 377
    02-12-2017, 08:38 PM Go to last post
  8. Need Help!- unlock code for BOSCH CNC CC220

    Started by JuanMatus‎, 12-15-2008 04:46 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 11,884
    02-12-2017, 01:52 PM Go to last post
    • Replies: 0
    • Views: 184
    02-07-2017, 09:58 AM Go to last post
    • Replies: 4
    • Views: 503
    02-06-2017, 09:41 AM Go to last post
    • Replies: 1
    • Views: 179
    02-04-2017, 07:07 PM Go to last post
  9. CNC Router Drive - Build or Buy?

    Started by JeremyFXDWG‎, 01-30-2017 12:45 AM
    cnc, cncrp, diy, setup, spindle
    • Replies: 6
    • Views: 595
    01-30-2017, 11:18 PM Go to last post
  10. Need Help!- advice please, conversion to mach 3, Leetra MPC6610 controller

    Started by tomcord‎, 01-24-2017 05:30 AM
    • Replies: 3
    • Views: 260
    01-27-2017, 03:30 PM Go to last post
  11. Need Help!- Can TNC 407 Do simultaneous 4 axis cut

    Started by Behnod‎, 01-27-2017 05:17 AM
    4axis, axis, heidenhain, simultanius, tnc407
    • Replies: 3
    • Views: 153
    01-27-2017, 09:02 AM Go to last post
  12. Question Newbie- Closed loop system

    Started by Enerik‎, 01-24-2017 01:05 PM
    closed loop system, encoders, mach4, motion controller board, roland mdx-40
    • Replies: 0
    • Views: 195
    01-24-2017, 01:05 PM Go to last post
  13. NUM 720B Repair

    Started by Steven123‎, 05-29-2008 09:17 AM
    2 Pages
    1 2
    not
    • Replies: 15
    • Views: 4,878
    01-19-2017, 09:01 AM Go to last post
  14. Need Help!- GILDEMEISTER with grundig eltropilot controller

    Started by russel1712‎, 06-28-2010 05:07 PM
    • Replies: 11
    • Views: 6,996
    01-19-2017, 03:33 AM Go to last post
  15. Need Help!- Newbie - communicating with old OSAI Series 10 controller units

    Started by GeometryShop‎, 05-31-2016 10:31 AM
    • Replies: 1
    • Views: 500
    01-18-2017, 05:33 PM Go to last post
  16. Newbie- OSAI for new cpu

    Started by ncarter‎, 01-10-2017 12:03 PM
    cnc, cpu, osai, running, transfer
    • Replies: 1
    • Views: 213
    01-17-2017, 01:37 PM Go to last post

Page 1 of 56 1234 11 51 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 11 users browsing this forum. (1 members & 10 guests)

  1. mifoma

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands