Controller & Computer Solutions


Page 1 of 55 1234 11 51 ... LastLast
Threads 1 to 20 of 1097

Forum: Controller & Computer Solutions

Discuss computers and setups for cnc controllers.

  1. Need Help!- Rambo 5v cnc milling machine

    Started by protopaja‎, 03-20-2014 08:31 AM
    #00, rambo, then
    • Replies: 1
    • Views: 519
    Today, 08:06 AM Go to last post
  2. Heidenhain 530 Kinematic adjustement problem

    Started by barefr‎, 02-15-2017 07:06 PM
    cut, cycle, kinematic, peace
    • Replies: 0
    • Views: 130
    02-15-2017, 07:06 PM Go to last post
  3. New Control Cabinet for UCCNC or EdingCNC

    Started by jon8949‎, 02-02-2017 06:32 PM
    • Replies: 10
    • Views: 350
    02-12-2017, 08:38 PM Go to last post
  4. Need Help!- unlock code for BOSCH CNC CC220

    Started by JuanMatus‎, 12-15-2008 04:46 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 11,804
    02-12-2017, 01:52 PM Go to last post
    • Replies: 0
    • Views: 172
    02-07-2017, 09:58 AM Go to last post
    • Replies: 4
    • Views: 428
    02-06-2017, 09:41 AM Go to last post
    • Replies: 1
    • Views: 160
    02-04-2017, 07:07 PM Go to last post
  5. CNC Router Drive - Build or Buy?

    Started by JeremyFXDWG‎, 01-30-2017 12:45 AM
    cnc, cncrp, diy, setup, spindle
    • Replies: 6
    • Views: 526
    01-30-2017, 11:18 PM Go to last post
  6. Need Help!- advice please, conversion to mach 3, Leetra MPC6610 controller

    Started by tomcord‎, 01-24-2017 05:30 AM
    • Replies: 3
    • Views: 242
    01-27-2017, 03:30 PM Go to last post
  7. Need Help!- Can TNC 407 Do simultaneous 4 axis cut

    Started by Behnod‎, 01-27-2017 05:17 AM
    4axis, axis, heidenhain, simultanius, tnc407
    • Replies: 3
    • Views: 145
    01-27-2017, 09:02 AM Go to last post
  8. Question Newbie- Closed loop system

    Started by Enerik‎, 01-24-2017 01:05 PM
    closed loop system, encoders, mach4, motion controller board, roland mdx-40
    • Replies: 0
    • Views: 185
    01-24-2017, 01:05 PM Go to last post
  9. NUM 720B Repair

    Started by Steven123‎, 05-29-2008 09:17 AM
    2 Pages
    1 2
    not
    • Replies: 15
    • Views: 4,859
    01-19-2017, 09:01 AM Go to last post
  10. Need Help!- GILDEMEISTER with grundig eltropilot controller

    Started by russel1712‎, 06-28-2010 05:07 PM
    • Replies: 11
    • Views: 6,969
    01-19-2017, 03:33 AM Go to last post
  11. Need Help!- Newbie - communicating with old OSAI Series 10 controller units

    Started by GeometryShop‎, 05-31-2016 10:31 AM
    • Replies: 1
    • Views: 492
    01-18-2017, 05:33 PM Go to last post
  12. Newbie- OSAI for new cpu

    Started by ncarter‎, 01-10-2017 12:03 PM
    cnc, cpu, osai, running, transfer
    • Replies: 1
    • Views: 204
    01-17-2017, 01:37 PM Go to last post
  13. Anilam to PC upgrade

    Started by jim_cliff11‎, 11-23-2016 07:48 AM
    2 Pages
    1 2
    • Replies: 23
    • Views: 808
    01-17-2017, 12:46 PM Go to last post
  14. Baumuller DKE 132M66 Spindle parameters

    Started by raviswanadha‎, 01-17-2017 09:57 AM
    baumuller, dke, machine, main, spindle
    • Replies: 0
    • Views: 172
    01-17-2017, 09:57 AM Go to last post
  15. Seeking advice on converting machine to either Mach or LinuxCNC

    Started by BMcCaskill‎, 12-30-2016 01:14 PM
    2 Pages
    1 2
    card, engineering, glentek, machine, software
    • Replies: 14
    • Views: 558
    01-10-2017, 11:57 AM Go to last post
    • Replies: 0
    • Views: 211
    01-05-2017, 12:13 PM Go to last post
  16. Need Help!- RICHAUTO A11E - No USB?

    Started by CHINNO‎, 12-30-2016 03:17 AM
    cnc, computer, controller, sticks, usb
    • Replies: 1
    • Views: 254
    12-31-2016, 07:06 PM Go to last post

Page 1 of 55 1234 11 51 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 9 users browsing this forum. (0 members & 9 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands