NC-Corrector, New Free G-code Editor for testing

[CyberPunk]

sorry for my english.
I ask you to test my G-code editor.
Written in vb6 + OpenGL

NC-Corrector Download http://nc-corrector.inf.ua/Downloads/NC4_setup.exe

[Ashish B]

Hey,
the GUI & the speed looks nice to me!

Is it a BETA release of NC PLOT Software ?

Thanks

[CyberPunk]

Hey,
the GUI & the speed looks nice to me!

Is it a BETA release of NC PLOT Software ?

Thanks

No, this is my personal development

[CyberPunk]

Available new version
Added Renumber blocks
Options renumbering in the Option/Setup/Machine/Block numbers

download link that the same

[neilw20]

Looks nice. The Tree is good.
When I swap tasks, and back to NC4 if the cursor is not over the graphics area, it does not repaint when task window is put into focus.
Needs a redraw call for whole task when task is bought to foreground.

[Ashish B]

Are you planning it to give (sell) SOURCE CODES to some software company?

Ash

[CyberPunk]

Are you planning it to give (sell) SOURCE CODES to some software company?

Ash

Yes.
Later.

[Biggles]

Hi,

I think your program is awesome. Runs quite smooth.

I work with Mach3 on my CNC and wondered if you were going to supply support for M codes like M98 and M99. I use it quite extensively as sometimes it's just quicker to type out some code than go the whole CADCAM route.

Thanks a million and hope it goes well from here.

[CyberPunk]

Hi,

I think your program is awesome. Runs quite smooth.

I work with Mach3 on my CNC and wondered if you were going to supply support for M codes like M98 and M99. I use it quite extensively as sometimes it's just quicker to type out some code than go the whole CADCAM route.

Thanks a million and hope it goes well from here.

What are you doing M98 and M99?
Standart is doing M98-Subprogram call, M99-Subprogram end.
This NC-Corrector understands.

Here's an example....



%
S500 M3
G54G90G0X-7.25Y-.25(START POINT OF FIRST CIRCLE TOP ROW)
G1G43H11Z.50F200.(TURN ON HEIGHT OFFSET - BRING TO .500 SAFETY PLANE)
M98P105(CALL SUBPROGRAM)
G90G0X-26.Y-.25
M98P105
G90G0X-44.75Y-.25
M98P105
G90G0X-63.5Y-.25
M98P105
G90G0X-82.25Y-.25
M98P105
G90G0X-82.25Y-19.(FIRST CIRCLE SECOND ROW)
M98P105
G90G0X-63.5Y-19.
M98P105
G90G0X-44.75Y-19.
M98P105
G90G0X-26.Y-19.
M98P105
G90G0X-7.25Y-19.
M98P105
G90G0X-7.25Y-37.75(FIRST CIRCLE THIRD ROW)
M98P105
G90G0X-26.Y-37.75
M98P105
G90G0X-44.75Y-37.75
M98P105
G90G0X-63.5Y-37.75
M98P105
G90G0X-82.25Y-37.75
M98P105
M30

O105(18 IN CIRCLES - SUBPROGRAM)
(STARTS 2" RIGHT OF TOP OF CIRCLE)
G91G1G42D1X-1.Z-1.30F200.(COMP ON - RAMP DOWN)
(Z VALUE REPRESENTS SAFETY PLANE & 3/4 BOARD & THRU CUT - .50+.75+.05=1.30)
X-1.F400.
G02J-9.(FULL CIRCLE - J VALUE DEFINES RELATIVE LOC OF CENTER POINT)
G01X-1.
G40X-1.Z1.30(COMP OFF - RAMP UP TO SAFETY PLANE)
M99(RETURN TO MAIN PROGRAM)

[Biggles]

Hi in the small example below it seems to ignore the L5 and only performs the function once.

Using M98-M99 this way allows you to describe a profile or pocketing path and then repeat it over. Perhaps the NC Corrector uses a different syntax. I run my machine on Mach3. NC Corrector is still excellent and I'll be playing around with it much more. Thanks very much for the program.

#1=0
g00 z50
x0 y0
M98 P100 L5
m30

O100
g00 z50
x#1 y0
g00 z0
g01 z-1
y100
g00 z5
#1=[#1+100]
m99

[CyberPunk]

Will in the near release..

[lancut]

Does this program recognizes an INCH scale? I can't make work with an inch...