![]() | |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| CNCzone Club House Discuss everything in between CNC. THIS IS NOT A TRASH BIN. |
| This forum is sponsored by: |
![]() |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#2
| ||||
| ||||
| Mike, The first time coming to the Zone can be overwhelming to a new member. There is so much information, and that can be very intimidating. I believe that since some of the older members are seasoned veterans they might tend to be a little short or seem to talk down to the new member. Its easy to forget that, in order to teach you have to take your time. When the new member does not get a answer right away they think they are being snubbed or they might lose there patience and leave. Many of the new members never get welcomed to the Zone, its not easy to be a outsider. The wealth of talent, information, ingenuity. and generosity of the CNC Zone are why they should stay. There are to sides to every coin. Jeff... Last edited by jalessi; 06-12-2008 at 03:00 PM. Reason: missed many positive points. |
|
#3
| ||||
| ||||
my .02 I am a member of a forum that has far more rules, and far less welcoming members and it is one of the largest internet forums in the world with 100,000+ members and 2.5 million threads. (63 million posts) I would say its a tie between the unwelcoming layout (this site has way to many sections, fewer sections would mean faster replies) and that when most people register, its because they have a problem that they couldn't find by searching and only stay for the problem discussion. |
|
#4
| ||||
| ||||
| Kyle, Very good point, I agree 100 percent. Jeff...
|
|
#5
| ||||
| ||||
| It's a hectic world. Some people are too busy to get hooked on forum posting. Others may be too busy reading the forum to post. (There is a tremendous amount of knowledge here.) Many are just too shy. CR. |
| Sponsored Links |
|
#6
| |||
| |||
| Still I guess if they did stay around then they would become familiar and probably start intimidating also.
__________________ An open mind is a virtue...so long as all the common sense has not leaked out. |
|
#7
| |||
| |||
| Hopefully they are all out making chips ![]() I'm mostly new, and posting my "I thinks" vs. the "I knows" of some of the very experienced and knowledgeable people here for me is imposing. But hey, I'll sometimes contribute if I can. It's not often! You can also easily wait, and watch for a really good answer. Lurk long enough, and you can start to answer the FAQ's. There is a ton of specialized info... and it is hard to grasp it all. Mike |
|
#9
| ||||
| ||||
| Hi All, Although fairly new and not posting very often, I do read ALL that I can on this forum. Usually attempting to find information on what I am presently doing on my project. The people who post are many and the information is tremendous. In my own build, taking too long, I constantly come up against something or other for which I need data. I search and read. Then I draw it up and then I make another part. Not being a machinist or electronic technician, it is hard but can be done. All the comments to various questions are extremely informative. I think the people are great and very seldom have I read anyones posts and seen the seen the shortness. Then they immediately apologize. Perhaps, I will contribute more as time goes on. Now I just post when I feel support is needed. Al |
|
#11
| ||||
| ||||
| It is good to remember to take some posts with a grain of salt as well. We all have a different sense of humour and different experiences.
__________________ www.integratedmechanical.ca |
|
#12
| |||
| |||
__________________ An open mind is a virtue...so long as all the common sense has not leaked out. |
![]() |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Virtual People | Twistr | Product Announcements & Manufacturer News | 1 | 03-05-2009 07:32 AM |
| Any DIY CNC people in Springfield Va? | Nitroghost | DIY-CNC Router Table Machines | 0 | 12-24-2007 06:57 AM |
| Old Threads Disappear | Mr.Chips | Forum Questions or Problems | 3 | 09-29-2007 09:10 AM |
| Bay City, MI CNC people! | cncjobs | Employment Opportunity | 0 | 05-08-2006 03:48 PM |
| Any R/C people using this circuit? | Al_The_Man | Parts for Radio Control Models | 1 | 03-22-2005 11:48 AM |