Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics - Page 3


Page 3 of 3 FirstFirst 123
Results 25 to 31 of 31

Thread: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

  1. #25
    Registered
    Join Date
    Apr 2013
    Location
    Sweden
    Posts
    1152
    Downloads
    2
    Uploads
    0

    Default Re: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

    Quote Originally Posted by RCaffin View Post
    The Enable signals in Mach3 are a trap for the unwary. They are NOT Output pins. They are meant to be used to enable the motor drivers, but I suspect few ever use them for that. They jiggle up and down when the eStop is activated, and I found them unusable in practice myself.

    Cheers
    Roger
    Must be something wrong there... My Enable is stable, low or high, depending on the state of Estop.

    https://adapting-camera.blogspot.com
    https://www.youtube.com/channel/UC_vrAWOz5YGX6_e3qtXg3YA


  2. #26
    Gold Member
    Join Date
    Jun 2010
    Location
    Australia
    Posts
    2479
    Downloads
    0
    Uploads
    0

    Default Re: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

    Well, when I said they 'jiggle', I was exaggerating slightly. You, the USER, do not have full control over them as the state of the eStop affects them, and they change state during power-up. This is as A_Camera says.

    The big problem with them in my real situation is that they are not compatible with the Gecko 203V servo drives. The Enable input on the Gecko is also the Fault output, so you can't just push it Hi or Lo. You have to sense it as well as driving it. In most cases today it may be best to just ignore them imho.

    Cheers
    Roger



  3. #27
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    United States
    Posts
    28566
    Downloads
    0
    Uploads
    0

    Default Re: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

    Changing state on power up is an issue with the parallel port, no?

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  4. #28
    Gold Member
    Join Date
    Jun 2010
    Location
    Australia
    Posts
    2479
    Downloads
    0
    Uploads
    0

    Default Re: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

    Changing state on power up is an issue with the parallel port, no?
    I'll plead ignorance there as I have never used the PP - although I am sure you are right.

    Cheers
    Roger



  5. #29
    Registered
    Join Date
    Jan 2013
    Location
    USA
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default Re: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

    I plan to use fusion360 for CAD/CAM. There are UCCNC, Mach3Mill, and CNC Router Parts (Mach3Mill) posts created. The UCCNC is a 'nc' extension while Mach3Mill is a 'tap' extension. The CRP parts post is not much different than the Mach3Mill.

    Does anyone know which option is correct to use - generic UCCNC, changing the extension of the CRP (Mach3Mill), or having a CNC Router Parts (UCCNC) developed?



  6. #30
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    United States
    Posts
    28566
    Downloads
    0
    Uploads
    0

    Default Re: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

    The UCCNC post has been updated several times in the last few weeks, so it's probably the most up to date.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  7. #31
    Registered
    Join Date
    Jan 2013
    Location
    USA
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default Re: Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics

    Quote Originally Posted by ger21 View Post
    The UCCNC post has been updated several times in the last few weeks, so it's probably the most up to date.
    I noticed in the CNC Router Parts post that a function was added to control a dustcollector. I didn't see that in the UCCNC code. Is that something that needs to be added?



Page 3 of 3 FirstFirst 123

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics
Swap Mach 3/ESS for UCCNC/UC300ETH-5LPT on CRP PRO with Plug and Play Electronics