Where can I find Xilog software? - Page 2


Page 2 of 3 FirstFirst 123 LastLast
Results 13 to 24 of 31

Thread: Where can I find Xilog software?

  1. #13
    Service SCM BR
    Guest

    Default

    What the version of xilog you need?


    Enviado do meu iPhone usando o Tapatalk



  2. #14
    Registered
    Join Date
    Aug 2014
    Location
    new Zealand
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    Hi Guys, I know this is an old conversation....but I have a Author 213 and am despirately trying to get it going... I have downloaded the XilogPlus from below link...but at NC configuration, it asks for password?????? what will this passw be?

    I am connected to my A213 via RS232 and PC...Am trying to connect to NC with XilogPlus.


    Thanks



  3. #15
    Registered
    Join Date
    May 2013
    Location
    Russia
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    1. password - xilog3
    2. your machine serial number, please



  4. #16
    Registered
    Join Date
    Aug 2014
    Location
    new Zealand
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    Thanks Barada..

    Serial is
    AL1645



  5. #17
    Registered
    Join Date
    May 2013
    Location
    Russia
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    wow, 1994 - too old for me.
    it is TRIA4000, try old password - MORBI
    all what scm have:
    we dot tl slash GZ9hgJs3Dk
    change dot and slash with . and /, without space.
    warning - proceENG1 it is manual for TECH100 with KLETRA, but procedure restore parameters for TRIA must be same. Also, by direct mail to scm service in italy, you can get parameters and plc for machine.



  6. #18
    Service SCM BR
    Guest

    Default Re: Where can I find Xilog software?

    Auckcabs, I working for the SCM Group in Brazil(SCMTecmatic) and say for you load Software Tria and Parametrs and data of PLC not is easy the work. But you can try, you need the all data and Floppy Drives formated in the macchine.
    Only in this way will you be able to get a bit of success in this endeavor.
    The phone number of our service in Italy is: +39 0541 700100.

    Probably you will be directed to the support of coach Sir Giuseppe Andreani or Montanari Because your machine is already an old machine and few know her to be able to support.
    Where machine is installed? What Country and City?

    Sorry for my English.
    If you speak Italian or Spanish I would prefer because it could express myself better. So that you fully understand me.



    Enviado do meu iPhone usando o Tapatalk



  7. #19
    Registered
    Join Date
    Oct 2014
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    SERVICE SCM BR
    Thank you for being around. I am looking for a copy of XILOG3 or XILOG PLUS for our TECH80 CNC Router. The machine serial is AL1 / 003412. The original computer that came with the XILOG3 software is "dead" and we have survived of making "ghost copies" from the HD. We are in our third machine in 10 years of use, and on the 4 or 6th HD. If you want you can answer me in Portuguese. We are located at Jacareí SP. Our NC is a KVARA6 and the machine is running on WINDOWS 98SE. The machine was both brand knew around 2001-2002 by a company named MADEPINT and then passed to us as part of a labor lawsuit payment.



  8. #20
    Registered
    Join Date
    Jun 2011
    Location
    uk
    Posts
    22
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    Contact SCM service department via e-mail



  9. #21
    Registered
    Join Date
    Aug 2014
    Location
    new Zealand
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    Thank you Barada...very uselfull info. However..the NC is working fine, I have already loaded the PLC and PAR files previously using a similar schematic. The big issue is that I cannot get the NC to read a .PGM file....I keep getting the error "Invalid File Format"

    More searching over the internet leads me to believe that this old NC requires a file called cnvrt1.1.exe to convert to PGM files and not WinXiso



  10. #22
    Registered
    Join Date
    Aug 2014
    Location
    new Zealand
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    Thanks for that Service SCM BR....the problem is not the PLC and PAR files...it is to get the NC to open/edit .PGM file created with Xilog.



  11. #23
    Registered
    Join Date
    Jan 2015
    Location
    Spain
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    We are a little carpenter's workshop (3 coworkers) and we have purchased an old machine at auction module. We had expectations improving our productivity, but sincerely, we have no idea how we could optimize times programing our machine out of TRIA7500. We can only program it by typing out the manually in the machine consuming excessive time.

    Is Xilog the appropriate software to be able to program our machine in an easier way?
    Where could find the necessary software?
    How to install Xilog on my PC?
    Do exist a manual or tutorial for Xilog?
    Is it necessary to downgrade the OS to 32bits in order to use Xilog?

    Thank you in advance!

    Machine: Morbidelli 503
    Year: 1997
    Serial Number: AL3514



  12. #24
    Registered
    Join Date
    Aug 2014
    Location
    new Zealand
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Where can I find Xilog software?

    @AntonioC

    We purchased the A213 (tria7500) a while back on auction and took me 2 months and countless hours on the net to figure this out.

    For our NC, xilog and xilog plus does not work as the NC does not recognise the .PGM file format.

    This is how we resolved it:
    1. We open the .DXF file in Aphacam and save it as .ANC file.
    2. We rename the .ANC file to .TXT file
    3. then we use the CN75NEW.exe file, run in DOS mode to convert the .TXT file to .PGM
    4. We then send the file via NULL-MODEM cable to NC
    5. Open the file in EDITOR on NC and verify it.

    Done..

    Hope this helps...send me an email if you require more info or any of the files etc

    mail at aucklandcabinets dot co dot nz



Page 2 of 3 FirstFirst 123 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Where can I find Xilog software?
Where can I find Xilog software?