Arrow CT C80010 Memory module needed - CNCzone.com-The Largest Machinist Community on the net!

Larry Callahan · #1 06-17-2009, 10:24 AM

We are in need of a CT C80010 memory module. Does anyone have a spare one to sell or perhaps retrofitted one and are selling off the parts?

I believe these are found on both the Arrow 500 and 1000 with a CT control.

Mr Bonavita · #2 06-21-2009, 09:07 AM

My friend, I"ll like to know what is the problem with the one you have?.
I think I can help you.

Larry Callahan · #3 06-22-2009, 09:36 AM

The data became corrupted and while re-loading the software it died completely. When you turn on the machine you wind up with a blank CRT. We moved the memory module to another machine and the problem follows the module.

Thoughts?

yours_prabhat · #4 06-22-2009, 10:49 AM

Originally Posted by Larry Callahan

We are in need of a CT C80010 memory module. Does anyone have a spare one to sell or perhaps retrofitted one and are selling off the parts?

I believe these are found on both the Arrow 500 and 1000 with a CT control.

I can send the memory Module for you communicate me on prabhatmishra@mail.com or on +91-9430737981
Regards
Prabhat Mishra

Mr Bonavita · #5 06-22-2009, 12:54 PM

Prabhat is your email correct??

Mr Bonavita · #6 06-23-2009, 10:36 AM

Larry did you get a new module ?

masamayoa@hotmail.com

Larry Callahan · #7 06-23-2009, 10:41 AM

No, I am still in need of a C80010 Memory Module.

Mr Bonavita · #8 06-23-2009, 10:57 AM

I have a arrow 500 it has a CT control, I can not make it work it has something
wrong with the parameters, and I was thinking about selling in parts for anyone
that may need spare parts.
I will now this afternoon .
It has new spindle drive, new "y" servo drive , new I/O module.
I can make it move by hand but it dos not run in auto mode.
I'll let you now .

masamayoa@hotmail.com

Larry Callahan · #9 06-23-2009, 12:36 PM

Thanks.

If you decide to part it out let me know. I may want other items.

Mr Bonavita · #10 06-23-2009, 04:15 PM

What else do you need ?
where are you located at in the US?

I'm in Long Beach Ca.

masamayoa@hotmail.com

Larry Callahan · #11 06-23-2009, 04:24 PM

We are in Camarillo, Ca.

We might need a power supply and who knows???? I guess depending on cost everything electrical to support the 3 we have.

Larry Callahan · #12 06-30-2009, 09:42 AM

Any thoughts on parting it out yet? Our machine is still down.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FNC-5 memory module failed on back-up	laser2500	German CNCzone	1	01-22-2009 10:00 PM
Need Help!- Mitsubishi memory card FX727B needed	ronmor	Mazak, Mitsubishi, Mazatrol	3	02-10-2008 10:54 AM
if you need ic and module,please tell me.	keithshen	Want To Buy...Need help!	0	01-07-2008 07:07 AM
Cincinatti Arrow Service Needed	mlkaiser99	Machine Problems, Solutions , Wireless DNC, serial port	0	09-14-2007 01:42 PM
Cincinnati Arrow 500E help needed....	Txshane	General CNC (Mill and Lathe) Control Software (NC)	0	05-11-2007 07:58 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)