Cincinnati Arrow error 9036 HELP!

[cncwork]

Hello,



Can anyone help with this alarm error 9036 static RAM file system corrupted?
It discription in the manual is (There is a proplem with the C: drive file system possibly due to a battery failure.

These machines are 1994 cincinnati milacron arrow 500 that have a control techniqes interface

The alarm comes up while booting up and can not go further. I have two of these machines that are idenical one is running.

Thanks in advance for your help.

CNC Programming, Inc.
cncprogram@comcast.net
253-514-1047

Similar Threads:

• Arrow 750 with CT control error message 9036
• Need Help!- error 9036 static RAM file system corrupted in cincinnati arrow 500 1994
• New Cincinnati Arrow owner with servo error
• Cincinnati milacron 750 arrow error msg
• Need Help!- Cincinnati Milacron Arrow 750 Error Message

[scudzuki]

According to the operating manual, error 9036 static RAM file system corrupt,
"There is a problem with the C: drive file system, possibly due to a battery faliure. Use test mode to check the file system. See section 5.3"
Unfortunately, these are the worst laid out manuals I have ever seen, and although there are quite a few section 5.3s, none that I have found in ANY of the 4 manuals have anything to do with diagnosing this error. If you have not done it already, you should record the axis parameters for the machine. I will email you the info I have for recording/entering those parameters.

Joe

[cncwork]

Hi Joe,

Thank you for your help. Looks like I need to be prepared to have a pc with Dos installed.
I'll keep you updated on my progress.

CNC Programming, Inc.
Matt

[Stickerman]

It's been a couple of years ago, but I had a memory error on my CT control. Maintenance Technologies had me download the files to my PC then copy them back onto the control which fixed the error.

Give Maintenance Technologies a call and they will walk you through it. www.maint-tech.com

[yuyin]

i need help, my HDD is brooked for the Cincinnati Milacron, any body has this software, thank you

[Daniel Algarve]

Hi Joe

I am Daniel and i need help in restoring my machine with the error 9036 static ram file system corrupt. How do I use the test mode to check the file system? My email is:
danielmendesalgarve@gmail.com and my machine is a CINCINNATI ARROW 500 with CT control FNC-5-005.THANKS IN ADVANCE

Daniel

[Daniel Algarve]

It's been a couple of years ago, but I had a memory error on my CT control. Maintenance Technologies had me download the files to my PC then copy them back onto the control which fixed the error.

Give Maintenance Technologies a call and they will walk you through it. www.maint-tech.com

I have the files but how can i download then onto the control? Can you help me please.My email is: danielmendesalgarve@gmail.com. Thanks in advance.
The alarms i have are: 9036,9070, and 9044. can yuo give me the cable pinout and tell me the right software for the download of the files please.
Best regards,

Daniel.

[Chivo]

I had the same problem years ago. Robert Varney help me. The MAIN.PLC file is for the next version of the machine software.


Executive
FNC Executive- standard version
Executive part number C50000
Executive Revision Rev 2.568

System Program
System Program 2.567

PLC
CM Arrow
91202654
P0.11

Robert Varney wrote:

The 9036 alarm is telling you that there is corrupted data in the Main.PLC file. It may be possible to go into test mode and file maintenance call up that file and look through it to find the corruption. It should give you a line number of where the corruption is.

The corruption could be caused by bad batteries in the memory card. With the power on replace the 2 AA batteries.


Robert Varney,
Application Engineer

MAG IAS
Global Services
1780 Worldwide Blvd.
Hebron, Ky 41048
U.S.
tel: 859-534-4748
fax: 859-534-4999
mobile: 513-375-1059

[Chivo]

Open the attached main.plc file in windows notepad and compare to what you have. Do not try to copy this file into your control you can only compare it and make manual edits if you need to. The picture of the screen you sent is normal.


Robert Varney,
Application Engineer

MAG IAS
Global Services
1780 Worldwide Blvd.
Hebron, Ky 41048
U.S.
tel: 859-534-4748
fax: 859-534-4999
mobile: 513-375-1059

[Chivo]

On your pc put a copy of cnc_com in a directory\folder by itself. Start cnc_com in a dos window\dos prompt. In file maintenance go to copy file. In there you will see copy from and copy to.
Copy from C;main.plc
Copy to I:main.plc
Copy in ASCII.

The RS232a port is drive I and the RS232b port is the J drive.



Robert Varney,
Application Engineer

MAG IAS
Global Services
1780 Worldwide Blvd.
Hebron, Ky 41048
U.S.
tel: 859-534-4748
fax: 859-534-4999
mobile: 513-375-1059

[Chivo]

On the machine once you call up the file to look at it you can change it when you exit out of the file there should be an option for exit and save.



Robert Varney,
Application Engineer

MAG IAS
Global Services
1780 Worldwide Blvd.
Hebron, Ky 41048
U.S.
tel: 859-534-4748
fax: 859-534-4999
mobile: 513-375-1059

[Daniel Algarve]

Hi Chivo

Thanks for your help. Next week i will try to have a look at the files and i will let you know .
Thaks.

Daniel

[Cumminsturbo94]

Daniel,
Did these backups and procedure fix your machine? I'm experiencing the same errors. I have my machines original backups but I'm having trouble communicating with the machine. I purchased the machine with bad batteries and trying to start it up for the first time since owning it.
Thanks,
Tom

[aventtini888]

hi guys this is the backup of a arrow 500 with CT control anyone know how to load them up to machine?

[pfp]

Hi did you fix your problem aventtini

[aventtini888]

Hi did you fix your problem aventtini

Make a cable , get the software from last post send it that msdos software And Upload parameters

[ieratec]

Hello,
Can anyone help me with arrow 500 boot ? I'm receiving the error 9036 and 9070, after that goes to the test mode screen and I can't load any files to the machine. Does anyone know how to pass the test mode ?

I appreciate any help my email is ieratec@bol.com.br

[12345678zxc]

hi guys this is the backup of a arrow 500 with CT control anyone know how to load them up to machine?

Same issue. How to load machine? Cable what is pin wiring order?

[pfp]

Hi you need computer with old version of windows up to XP
Cable Configuration

9 pin 25 pin

1 8
2 2
3 3
4 6
5 7
6 20
7 5
8 4
9 1
You also require the cnc_com.exe which should be on one of the posts in a zip file. Also patience is very important.

[12345678zxc]

Thanks a lot! Need test.