Differences between DSP RZNC-D5416 and RZNC-0501

[KDRusty]

Hi,

I just received my K6100A yesterday and noticed that mine came with a DSP Model RITHNC-053XSI-L30 with Version software RZNC-D5416. SkipW just received his K6100A a few weeks earlier than me and his came with a DSP RZNC-0504. From other post on CNCzone and website searches the common model is the RZNC-0501. Does anyone know what the differences in these unit are? Can't seem to find anything good searching the web.

Thanks
KDRusty

[SkipW]

After talking to KDRusty about the DSP controller he received, and I hope he doesn't mind me mentioning this, but Quick CNC sent him a dusty USED DSP controller that had scratches on the screen and it even has a screw missing on the back. And as he mentioned previously, they didn't send a cable for it either.

That should never happen. We send money in good faith and expect to receive new components, not used older model items. This is bad advertisement for Quick CNC.

You can't blame Taney for this screw-up. He doesn't build the machines or package them for shipment, but he can correct the factory error. He should send KDRusty a brand new DSP that is pre-programmed for his K6100A. That's what I think anyhow.

[KDRusty]

Everything i read prior to getting the K6100A made me think i would be getting a RZNC-0501 DSP. But when the router arrived with the missing items I started looking closer at everything. Seen the scratches on the screen and said all well it will get scratched anyway. But then I noticed the screw missing, the case a little loose, minor scuffs, dust around the edge of screen and keypad. Then looking at the model # sticker made me wonder even more. Decided to plug the DSP into my laptop to see if i could power it up and went into the version software menu to see the RZNC-D5416 model.

Couldn't find anything but older post mentioning the RZNC-D5416. That one reason I think I might have received an older unit. Even sites selling new DSP don't even offer that model.

Taney assured me that the unit wasn't used but I have my doubts(i think maybe factory refurbished) and he did offer to exchange it if I sent the old one back first. Was hoping to have him send me a replacement with my missing items. He said the unit i received was set up for my machine and that they would need to reprogram the new DSP using the old unit. Fair enough...i will probably send it back once i verified the machine is running properly.

BTW, Taney, as always, been very quick to reply to all my inquires and i'm not worried at all. None of this I would blame on Taney but on whoever does the final quality check before crating the unit. He said my replacement parts are on their way so I'm hoping to get the machine running late next week.

So...if anyone has any information about the RZNC-D5416 please let me know I'm still curious on what i received.

Best Regards,
KDRusty

[draughted]

i just purchased one of these pendants alone. and got no english instructions and it was set on chinese.

can any of you help with an instruction sheet, or help getting to english.

[draughted]

my dsp controller also had scratches and bad packaging but that seem to be the way with these things.

mines the 0501 model you have mentioned

[SkipW]

Originally Posted by draughted i just purchased one of these pendants alone. and got no english instructions and it was set on chinese. can any of you help with an instruction sheet, or help getting to english.

Try this draughted.

[SkipW]

Originally Posted by draughted i just purchased one of these pendants alone. and got no english instructions and it was set on chinese. can any of you help with an instruction sheet, or help getting to english.

Found a youtube vid on changing DSP language from Chinese to English.

YouTube - How to change language to English on DSP control panel
I know someone posted instructions on the forum here for changing the language but I couldn't locate it. Hope this helps.

[draughted]

thanks that really helps!

i also found the instruction sheet from a british firm that sells similar DSP controllers
motioncontrolproducts.co.uk

[RICHNC]

Originally Posted by KDRusty Everything i read prior to getting the K6100A made me think i would be getting a RZNC-0501 DSP. But when the router arrived with the missing items I started looking closer at everything. Seen the scratches on the screen and said all well it will get scratched anyway. But then I noticed the screw missing, the case a little loose, minor scuffs, dust around the edge of screen and keypad. Then looking at the model # sticker made me wonder even more. Decided to plug the DSP into my laptop to see if i could power it up and went into the version software menu to see the RZNC-D5416 model. Couldn't find anything but older post mentioning the RZNC-D5416. That one reason I think I might have received an older unit. Even sites selling new DSP don't even offer that model. Taney assured me that the unit wasn't used but I have my doubts(i think maybe factory refurbished) and he did offer to exchange it if I sent the old one back first. Was hoping to have him send me a replacement with my missing items. He said the unit i received was set up for my machine and that they would need to reprogram the new DSP using the old unit. Fair enough...i will probably send it back once i verified the machine is running properly. BTW, Taney, as always, been very quick to reply to all my inquires and i'm not worried at all. None of this I would blame on Taney but on whoever does the final quality check before crating the unit. He said my replacement parts are on their way so I'm hoping to get the machine running late next week. So...if anyone has any information about the RZNC-D5416 please let me know I'm still curious on what i received. Best Regards, KDRusty

his is Jery form China,the CNC controller(RZNC or RICHNC) company!
RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd.
the RZNC-D5416 is one of important chip models for RZNC or RICHNC products, not matter RZNC-0501/0601/0701/0801 and so on. if the products is RZNC or RICHNC models, it must have this chip models on products ID.
if you have more questions you can send to richnc@hotmail.com. the company official email address.

[RICHNC]

Originally Posted by SkipW Found a youtube vid on changing DSP language from Chinese to English. YouTube - How to change language to English on DSP control panel I know someone posted instructions on the forum here for changing the language but I couldn't locate it. Hope this helps.

this is Jery form China,the CNC controller(RZNC or RICHNC) company!
RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd.
you can download the operation manual which you need from RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd. - RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd.
if you have more questions you can send to richnc@hotmail.com. the company official email address.

[RICHNC]

Originally Posted by KDRusty Everything i read prior to getting the K6100A made me think i would be getting a RZNC-0501 DSP. But when the router arrived with the missing items I started looking closer at everything. Seen the scratches on the screen and said all well it will get scratched anyway. But then I noticed the screw missing, the case a little loose, minor scuffs, dust around the edge of screen and keypad. Then looking at the model # sticker made me wonder even more. Decided to plug the DSP into my laptop to see if i could power it up and went into the version software menu to see the RZNC-D5416 model. Couldn't find anything but older post mentioning the RZNC-D5416. That one reason I think I might have received an older unit. Even sites selling new DSP don't even offer that model. Taney assured me that the unit wasn't used but I have my doubts(i think maybe factory refurbished) and he did offer to exchange it if I sent the old one back first. Was hoping to have him send me a replacement with my missing items. He said the unit i received was set up for my machine and that they would need to reprogram the new DSP using the old unit. Fair enough...i will probably send it back once i verified the machine is running properly. BTW, Taney, as always, been very quick to reply to all my inquires and i'm not worried at all. None of this I would blame on Taney but on whoever does the final quality check before crating the unit. He said my replacement parts are on their way so I'm hoping to get the machine running late next week. So...if anyone has any information about the RZNC-D5416 please let me know I'm still curious on what i received. Best Regards, KDRusty

this is Jery form China,the CNC controller(RZNC or RICHNC) company!
RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd.
you can download the operation manual which you need from RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd. - RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd.
if you have more questions you can send to richnc@hotmail.com. the company official email address.

[RICHNC]

this is Jery form China,the CNC controller(RZNC or RICHNC) company!
RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd.
you can download the operation manual which you need from RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd. - RZNC-0501,RZNC CNC Controller,RICHNC Drive,RICHNC Motor-Beijing RichNC Technology Co.,Ltd.
if you have more questions you can send to richnc@hotmail.com. the company official email address.