Editing teksoft procam Heidenhain post

[RMARCH]

Hi,

I was wondering if someone could help me out.
My problem is when my Procam2000 generates a program it does not input The X, Y Value of the CC of the arc center when one of the axises stays the same as the previous arc.

So my control gives me an error.

Example:

0 BEGIN PGM 0001 INCH
1 TOOL DEF 1 L+0 R.25
2 TOOL CALL 1 Z S3000
3 L X-.3169 Y+.6908 RL F3999 M03
4 L Z+.1 R0 F3999 M
5 L Z-.27 R0 F200 M
6 CC X+0. Y+.52
7 C X+.3169 Y+.6908 DR- RL F100 M
8 CC Y+0. X_______
9 C X+.6908 Y+.3169 DR- RL F100 M
10 CC X+.52 Y______
11 C X+.6908 Y-.3169 DR- RL F100 M
12 CC X+0. Y________
13 C X+.3169 Y-.6908 DR- RL F100 M
14 CC Y-.52 X________
15 C X-.3169 Y-.6908 DR- RL F100 M
16 CC Y+0. X _________
17 C X-.6908 Y-.3169 DR- RL F100 M
18 CC X-.52 Y ____________
19 C X-.6908 Y+.3169 DR- RL F100 M
20 CC X+0. Y _________
21 C X-.3169 Y+.6908 DR- RL F100 M
22 L Z+.1 R0 F3999 M
23 STOP M25
24 STOP M02
25 END PGM 0001 INCH



Thanks
Ray

[RMARCH]

Need Help PLEASE

[bert01980]

Hallo...
i give one help!!!

[RMARCH]

The Post processor is for the TNC2500 Control.

[Nandop]

Still looking for?
I have the post for TNC2500 ISO format.
Let me know.
Nandop.

[RMARCH]

Hi Nandop,

Thanks for offering your post but i already got one that works.

Thanks Again !!!

[RMARCH]

Still looking for?
I have the post for TNC2500 ISO format.
Let me know.
Nandop.

Hi Nandop,

Yes, i am still looking for a Procam TNC2500 ISO Format post.
Can you please send it to : RMarch1@comcast.net

I am also looking for post for TNC2500 conversational. I have one now but it doesn't do Arc's & Circles Correct.

Example:

0 BEGIN PGM 0001 INCH
1 TOOL DEF 1 L+0 R.25
2 TOOL CALL 1 Z S3000
3 L X-.3169 Y+.6908 RL F3999 M03
4 L Z+.1 R0 F3999 M
5 L Z-.27 R0 F200 M
6 CC X+0. Y+.52
7 C X+.3169 Y+.6908 DR- RL F100 M
8 CC Y+0. X_______
9 C X+.6908 Y+.3169 DR- RL F100 M
10 CC X+.52 Y______
11 C X+.6908 Y-.3169 DR- RL F100 M
12 CC X+0. Y________
13 C X+.3169 Y-.6908 DR- RL F100 M
14 CC Y-.52 X________
15 C X-.3169 Y-.6908 DR- RL F100 M
16 CC Y+0. X _________
17 C X-.6908 Y-.3169 DR- RL F100 M
18 CC X-.52 Y ____________
19 C X-.6908 Y+.3169 DR- RL F100 M
20 CC X+0. Y _________
21 C X-.3169 Y+.6908 DR- RL F100 M
22 L Z+.1 R0 F3999 M
23 STOP M25
24 STOP M02
25 END PGM 0001 INCH

When the CC is The same as the one before my post doesn't output any value but the control wants one.


Thanks so much !!!
Ray

[kudos]

sounds like you might need to try fource the post to output the Y, as its probly thinking the Y is same so no need to re output etc.

add a ! on end of the line that outputs the section u want to modd

eg
<Y!> instead of <Y>

maybe this will help, rob