| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| CamSoft Products Discuss Camsoft PC based CNC controller products here! |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#1
 
03-09-2008, 02:02 PM
| ||||
| ||||
Hi, Is it possible to use the Camsoft HMI software ie. cncpro with an other motion control card or software besids the Galil card or is it specific to the Galil motion card.. John.  |
|
#2
03-09-2008, 04:14 PM
| ||||
| ||||
| In addition to the galil cards, Camsoft has recently been advertizing their own real time motion control card at a considerably lower price. There's also an inexpensive stepper only card. May be more, but this is all I'm aware of. Karl |
|
#3
03-10-2008, 10:18 AM
| |||
| |||
| Yes it is possible. All in all we don't publish the actual brand names because we don't want to seem bias, we do have our favorites. Plus some models are modified to our specs. You can see a list of these here: Hardware category www.cnccontrols.com/motionboards.asp www.cnccontrols.com/digitalio.asp www.cnccontrols.com/microsystems.asp www.cnccontrols.com/products2.asp Software category www.cnccontrols.com/cncpro.asp www.cnccontrols.com/cncplus.asp www.cnccontrols.com/cnclite.asp www.cnccontrols.com/graphicaloi.asp Enclosure / Pendent category www.cnccontrols.com/touchscreen2.asp www.cnccontrols.com/hhpendant.asp www.cnccontrols.com/freestanding.asp www.cnccontrols.com/touchscreen3.asp www.cnccontrols.com/touchscreen4.asp www.cnccontrols.com/touchscreen5.asp www.cnccontrols.com/controlmate.asp www.cnccontrols.com/usbjogstick.asp Tech Support CamSoft Corp. support@camsoftcorp.com PH 951-674-8100 Fax 951-674-3110 www.cnccontrols.com
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) Last edited by camsoft; 03-10-2008 at 11:26 AM. |
|
#4
03-11-2008, 03:25 AM
| ||||
| ||||
| Thanks Camsoft i'll be checking the list out. Am I correct in saying that your Camsoft HMI software is not built to run with Fanuc Alpha AC servos and drives..at the moment or would it be possible to interface to these somehow...? Many thanks for your time, John. |
|
#5
03-11-2008, 11:59 AM
| |||
| |||
| John, The Alpha's are AC Brushless motors that we could use. It is the amp drives that we can't reuse. There are a few variations so we need to be careful. If you have the documentation for the power side cables from the motors themselves and hall sensors then we could go further to get the amp and volt ratings in order to quote you replacement amp drives to reuse these motors. Tech Support CamSoft Corp. support@camsoftcorp.com PH 951-674-8100 Fax 951-674-3110 www.cnccontrols.com
__________________ (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management) |
| Sponsored Links |
| |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| CamSoft.CBK | HillBilly | Machine Problems, Solutions , Wireless DNC, serial port | 1 | 12-10-2009 05:15 AM |
| What's the skibby on motion controllers? | hoga01 | General CNC (Mill and Lathe) Control Software (NC) | 13 | 03-06-2007 12:20 AM |
| PC Motion controllers | zoeper | Bridgeport and Hardinge Mills | 9 | 11-28-2006 08:03 AM |
| camsoft G1,G2,G3, | DARYL | CamSoft Products | 9 | 06-22-2006 03:38 PM |
| What's new at Camsoft | Karl_T | CamSoft Products | 0 | 03-31-2006 08:33 PM |
| | |
Linear Mode
