Results 1 to 7 of 7

Thread: EZ-Trak - b3t.exe

  1. #1
    Registered
    Join Date
    Oct 2009
    Location
    USA
    Posts
    4
    Downloads
    0
    Uploads
    0

    EZ-Trak - b3t.exe

    I have been trying to diagnose our EZ-Trak at the shop here and all problems are pointing to the BMDC board. From reading this forum, there appears to be a utility to help confirm this, B3T.exe. I am unable to find this file anywhere on the machine or our installation floppies. If someone could assist me with obtaining this file, I would greatly appreciate it!

    Thank you for your time!


  2. #2
    Registered
    Join Date
    Feb 2008
    Location
    US
    Posts
    204
    Downloads
    0
    Uploads
    0
    I have the B3t.exe that is for a TC-22 mill,don,t know if its the same.
    Looks like it detects BMDC3L,BMDC3 or BMDC4
    If someone can confirm its the same file you need I can email it to you.


  3. #3
    Registered
    Join Date
    Oct 2009
    Location
    USA
    Posts
    4
    Downloads
    0
    Uploads
    0
    tpmx57,

    Being that no one has responded yet -- Would you mind submitted the file anyways? BMDC3 sounds quite familiar, but I would have to pull the board to verify.

    Thanks again.


  4. #4
    Moderator
    Join Date
    Nov 2004
    Location
    USA
    Posts
    2,986
    Downloads
    0
    Uploads
    0
    B3T is only one version. The early boards ( BMDC in 2 axis EZTRAKs) do not identify themselves to the test but it can still be run.
    Hard to transfer a exe file. Most firewalls stop it.

    George
    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  • #5
    Registered
    Join Date
    Oct 2009
    Location
    USA
    Posts
    4
    Downloads
    0
    Uploads
    0
    Thanks for the information machintek. To bypass the firewalls, you can easily zip the file before sending via email. Alternatively, if anyone can help, I can provide FTP information to assist in the transfer. Private message me for contact information on how to send the file.

    Thanks!


  • #6
    Moderator
    Join Date
    Nov 2004
    Location
    USA
    Posts
    2,986
    Downloads
    0
    Uploads
    0
    Perhaps a Email address to send to?

    George
    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  • #7
    Registered
    Join Date
    Oct 2009
    Location
    USA
    Posts
    4
    Downloads
    0
    Uploads
    0
    You may send the file via email to dslezak at gmail.com

    Thanks in advance!


  • Similar Threads

    1. ez trak help
      By markj in forum CNCzone Club House
      Replies: 0
      Last Post: 06-24-2009, 02:29 PM
    2. trak dpm 3
      By kscarsdale in forum Mastercam
      Replies: 1
      Last Post: 03-11-2009, 11:19 AM
    3. Need Help!- SWI Trak CNC 2
      By kiwiavi in forum General CNC (Mill and Lathe) Control Software (NC)
      Replies: 0
      Last Post: 11-12-2008, 04:31 AM
    4. ez-trak
      By rsbbmw in forum Bridgeport and Hardinge Mills
      Replies: 6
      Last Post: 06-07-2007, 03:08 AM
    5. EZ-Trak
      By zdude in forum Bridgeport and Hardinge Mills
      Replies: 1
      Last Post: 10-20-2005, 08:32 PM

    Tags for this Thread

    Posting Permissions


     


    About CNCzone.com

      We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

    Follow us on

    Facebook Dribbble RSS Feed


    Search Engine Friendly URLs by vBSEO ©2011, Crawlability, Inc.