| |
| Home Page | Mark Forums Read | Today's Posts | My Replies | Classifieds | Reviews | Photo Gallery | Web Links | Share Files | Advertise With Us | Ad List |
| |||||||
| Bridgeport and Hardinge Mills Discuss Bridgeport and Hardinge Mills here! |
| | |
| This forum is sponsored by: |
 |
| | LinkBack | Thread Tools | Search this Thread | Display Modes |
|
#1
 
03-04-2006, 11:19 AM
| |||
| |||
Recently purchased Boss 8 R2E3 mill and am looking for the software used to drip feed programs. Would anyone be willing to email me a copy? Also would someone be willing to send me a copy of either the operators manual and or the programming manuals? Been browsing through all the posts and have learned a lot so far, but still need basics on how to operate machine. Thanks in advance to any and all!! sales@pdmechanical.com Last edited by pdmech; 03-05-2006 at 10:57 AM.  |
|
#2
03-05-2006, 03:13 PM
| |||
| |||
| I think we have an install cd of version 11 Ez-cam which has Ez-utility, also I think we have an extra application manual! Your welcome to them if you pay for shipping! P.S. The Ez-cam programming software will run but only in demo mode without a hardware key! The utility program will work without a key though! Larry |
|
#3
03-06-2006, 06:34 AM
| |||
| |||
| Thanks for the reply Larry. I'd be glad to pay shipping on it. I've included my zip code and email address, you can email me directly with the total amount. Also do you have any tips or suggestions for operating this software and or machine? Zip 13039 sales@pdmechanical.com Thanks again Larry |
|
#4
03-08-2006, 05:52 PM
| |||
| |||
| If you go to http://www.machinemanuals.net/categories.php you can buy maintenance, operating and programming manuals for this machine for $25 each. Doubt you will find then cheaper anywhere else. |
|
#5
03-09-2006, 06:10 AM
| |||
| |||
| Thanks for the info. I've already been there and see they are all on CD and I'd prefer one in print. I have new genuine Bport manuals on thier way any how. Actually the ezlink software seems to be more of a problem getting. MegaMoog was kind enough to send me the ezcam files but either my computer is giving me trouble or the files may be bad. Don't know yet. Thanks anyway. |
| Sponsored Links |
| |
|
#6
03-09-2006, 10:02 AM
| |||
| |||
| PD, Where are you at with the files,did they unzip ok? Can you burn to a CD? If so will the setup run and give you a choice as to what to install? There is another link on this site somewhere to Ez-utilities over at feature-cam which is the same utility, and its FREE! Larry ftp://ftp.featurecam.com/utls.exe |
|
#7
03-09-2006, 10:50 AM
| |||
| |||
| I was able to unzip but when I try to install my computer seems to take a "time out" on me. Not sure why. Going to have my nephew look at it this weekend. He's pretty good with that sort of thing. I'll check outb that link too. Thanks |
|
#8
04-14-2006, 10:35 AM
| |||
| |||
i have a 1984,1985 E2R4 and the programing i found to work better with older software. i have a copy of ezlinks with dos. i got it from MACHINETEK off is site the guy really knows what he's talking about. give me your e-mail and i will send it to you. Keith |
|
| | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | |
| |
| | |
Linear Mode
