Automation Technology Products


Page 1 of 24 123411 ... LastLast
Threads 1 to 20 of 467

Forum: Automation Technology Products

Discuss Automation Technology Products here.

  1. Which Power Supply Do I Need

    Started by Shanghyd‎, 09-23-2017 01:07 PM
    2.8a, 425oz, motors, power, supply
    • Replies: 0
    • Views: 101
    09-23-2017, 01:07 PM Go to last post
  2. KL 4030 driver problems?

    Started by Kev‎, 08-18-2017 10:47 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 682
    08-30-2017, 03:28 PM Go to last post
  3. Proximity sensor wiring

    Started by Lindzr‎, 08-12-2017 10:56 PM
    • Replies: 2
    • Views: 286
    08-15-2017, 08:29 PM Go to last post
    • Replies: 0
    • Views: 242
    07-24-2017, 10:53 PM Go to last post
  4. C11GS - Is there an updated wiring schematic?

    Started by Azalin‎, 07-16-2017 10:50 AM
    • Replies: 2
    • Views: 242
    07-21-2017, 02:52 PM Go to last post
  5. KL-300 Noise & runout

    Started by psykhon‎, 06-10-2017 10:34 AM
    high, kl-300, noise, pitch, runout
    • Replies: 0
    • Views: 356
    06-10-2017, 10:34 AM Go to last post
  6. Kelling Dip Switch Orientation???

    Started by ny_racer_xxx‎, 03-04-2016 04:28 PM
    2 Pages
    1 2
    0=off, 1=on, kitten, set, switch
    • Replies: 12
    • Views: 1,640
    04-24-2017, 02:45 PM Go to last post
  7. Need Help!- Current Settings for KL4042D Stepper Drivers and Stepper Motors

    Started by New Lathe Man‎, 04-01-2017 07:43 PM
    current, mode, set, software, stepper
    • Replies: 0
    • Views: 355
    04-01-2017, 07:43 PM Go to last post
  8. KL-8070D Software configured mode?

    Started by beltramidave‎, 03-30-2017 10:24 PM
    configured, dip, mode, setting, software
    • Replies: 5
    • Views: 271
    03-31-2017, 11:21 AM Go to last post
  9. C10 BOB + + USS + 5056D Drivers will not turn motor

    Started by Ambico‎, 06-04-2016 12:59 PM
    • Replies: 8
    • Views: 895
    03-29-2017, 09:50 AM Go to last post
    • Replies: 4
    • Views: 198
    03-28-2017, 08:59 PM Go to last post
  10. Solved Sunfar E300 series VFD reset-the spindle runs once again!

    Started by newcreations‎, 03-24-2017 10:33 AM
    deep, plunge, reset, sunfar, vcarve pro
    • Replies: 0
    • Views: 192
    03-24-2017, 10:33 AM Go to last post
  11. new machine help think my breakout board is fried

    Started by skinny1965‎, 01-27-2017 11:18 AM
    board, check, cnc, set, signal
    • Replies: 0
    • Views: 539
    01-27-2017, 11:18 AM Go to last post
  12. Mach 3, C11 BOB questions.

    Started by vz58‎, 12-10-2016 11:04 AM
    c11, input, led, mach, set
    • Replies: 1
    • Views: 530
    12-11-2016, 02:31 PM Go to last post
    • Replies: 0
    • Views: 267
    11-30-2016, 01:29 PM Go to last post
    • Replies: 2
    • Views: 750
    09-08-2016, 11:36 PM Go to last post
  13. KL8060 probleme

    Started by habibmgh‎, 08-19-2016 01:03 PM
    100khz, diffrent, kl-8056d, kl8060, product
    • Replies: 0
    • Views: 364
    08-19-2016, 01:03 PM Go to last post
  14. KL-6050 Stepper Driver Frustration

    Started by tjp912‎, 06-22-2016 10:00 PM
    3 Pages
    1 2 3
    cnc, electrical noise, kl-6050, motor driver, oscillation
    • Replies: 30
    • Views: 1,868
    06-24-2016, 02:37 PM Go to last post
  15. Limit Switch Help for Controller Box

    Started by Ron2d‎, 06-19-2016 06:21 PM
    box, cnc, controller, limit, wired
    • Replies: 0
    • Views: 507
    06-19-2016, 06:21 PM Go to last post
    • Replies: 6
    • Views: 901
    06-13-2016, 06:51 PM Go to last post

Page 1 of 24 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands