Automation Technology Products


Page 1 of 24 123411 ... LastLast
Threads 1 to 20 of 474

Forum: Automation Technology Products

Discuss Automation Technology Products here.

  1. Problem- KL-Series Drivers, Leadshine and Similar Import Drive wiring

    Started by datac‎, Today 07:09 PM
    dir, drives, flashcut, sense, source
    • Replies: 0
    • Views: 45
    Today, 07:09 PM Go to last post
  2. KL- 8060 Driver problem on new conversion

    Started by rcheli‎, 12-11-2017 09:53 PM
    item#, kl-8060, motor, nema34 steppers, stepper
    • Replies: 4
    • Views: 129
    Yesterday, 11:52 PM Go to last post
  3. Solved stepper knocks

    Started by Dean448‎, 12-10-2017 11:52 AM
    g540, kl-6050, kl23h251-24-8b, parallel, series
    • Replies: 1
    • Views: 84
    12-10-2017, 11:59 AM Go to last post
  4. Gecko G540 vs. KL-4030 drivers (and break out board)

    Started by cncuser1‎, 11-14-2017 10:22 PM
    board, drivers, g540, gecko, kl-4030
    • Replies: 4
    • Views: 462
    12-06-2017, 08:13 PM Go to last post
  5. Sloppy

    Started by joe90023‎, 11-27-2017 10:35 PM
    • Replies: 1
    • Views: 195
    11-28-2017, 10:40 AM Go to last post
    • Replies: 6
    • Views: 797
    10-02-2017, 06:16 PM Go to last post
  6. Question Need Help!- "peak current" or "reference current" configuration

    Started by Djsilva2005‎, 09-27-2017 02:23 PM
    amperage, config, drivers, stepper, temperature
    • Replies: 2
    • Views: 198
    09-27-2017, 04:43 PM Go to last post
  7. Which Power Supply Do I Need

    Started by Shanghyd‎, 09-23-2017 02:07 PM
    2.8a, 425oz, motors, power, supply
    • Replies: 0
    • Views: 215
    09-23-2017, 02:07 PM Go to last post
  8. KL 4030 driver problems?

    Started by Kev‎, 08-18-2017 11:47 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 821
    08-30-2017, 04:28 PM Go to last post
  9. Proximity sensor wiring

    Started by Lindzr‎, 08-12-2017 11:56 PM
    • Replies: 2
    • Views: 354
    08-15-2017, 09:29 PM Go to last post
    • Replies: 0
    • Views: 281
    07-24-2017, 11:53 PM Go to last post
  10. C11GS - Is there an updated wiring schematic?

    Started by Azalin‎, 07-16-2017 11:50 AM
    • Replies: 2
    • Views: 275
    07-21-2017, 03:52 PM Go to last post
  11. KL-300 Noise & runout

    Started by psykhon‎, 06-10-2017 11:34 AM
    high, kl-300, noise, pitch, runout
    • Replies: 0
    • Views: 375
    06-10-2017, 11:34 AM Go to last post
  12. Kelling Dip Switch Orientation???

    Started by ny_racer_xxx‎, 03-04-2016 05:28 PM
    2 Pages
    1 2
    0=off, 1=on, kitten, set, switch
    • Replies: 12
    • Views: 1,712
    04-24-2017, 03:45 PM Go to last post
  13. Need Help!- Current Settings for KL4042D Stepper Drivers and Stepper Motors

    Started by New Lathe Man‎, 04-01-2017 08:43 PM
    current, mode, set, software, stepper
    • Replies: 0
    • Views: 387
    04-01-2017, 08:43 PM Go to last post
  14. KL-8070D Software configured mode?

    Started by beltramidave‎, 03-30-2017 11:24 PM
    configured, dip, mode, setting, software
    • Replies: 5
    • Views: 299
    03-31-2017, 12:21 PM Go to last post
  15. C10 BOB + + USS + 5056D Drivers will not turn motor

    Started by Ambico‎, 06-04-2016 01:59 PM
    • Replies: 8
    • Views: 933
    03-29-2017, 10:50 AM Go to last post
    • Replies: 4
    • Views: 221
    03-28-2017, 09:59 PM Go to last post
  16. Solved Sunfar E300 series VFD reset-the spindle runs once again!

    Started by newcreations‎, 03-24-2017 11:33 AM
    deep, plunge, reset, sunfar, vcarve pro
    • Replies: 0
    • Views: 240
    03-24-2017, 11:33 AM Go to last post
  17. new machine help think my breakout board is fried

    Started by skinny1965‎, 01-27-2017 12:18 PM
    board, check, cnc, set, signal
    • Replies: 0
    • Views: 567
    01-27-2017, 12:18 PM Go to last post

Page 1 of 24 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 11 users browsing this forum. (1 members & 10 guests)

  1. rcheli

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands