Automation Technology Products


Page 1 of 24 1234 11 ... LastLast
Threads 1 to 20 of 461

Forum: Automation Technology Products

Discuss Automation Technology Products here.

  1. Kelling Dip Switch Orientation???

    Started by ny_racer_xxx‎, 03-04-2016 04:28 PM
    2 Pages
    1 2
    0=off, 1=on, kitten, set, switch
    • Replies: 12
    • Views: 1,154
    04-24-2017, 02:45 PM Go to last post
  2. Need Help!- Current Settings for KL4042D Stepper Drivers and Stepper Motors

    Started by New Lathe Man‎, 04-01-2017 07:43 PM
    current, mode, set, software, stepper
    • Replies: 0
    • Views: 234
    04-01-2017, 07:43 PM Go to last post
  3. KL-8070D Software configured mode?

    Started by beltramidave‎, 03-30-2017 10:24 PM
    configured, dip, mode, setting, software
    • Replies: 5
    • Views: 156
    03-31-2017, 11:21 AM Go to last post
  4. C10 BOB + + USS + 5056D Drivers will not turn motor

    Started by Ambico‎, 06-04-2016 12:59 PM
    • Replies: 8
    • Views: 781
    03-29-2017, 09:50 AM Go to last post
    • Replies: 4
    • Views: 126
    03-28-2017, 08:59 PM Go to last post
  5. Solved Sunfar E300 series VFD reset-the spindle runs once again!

    Started by newcreations‎, 03-24-2017 10:33 AM
    deep, plunge, reset, sunfar, vcarve pro
    • Replies: 0
    • Views: 91
    03-24-2017, 10:33 AM Go to last post
  6. new machine help think my breakout board is fried

    Started by skinny1965‎, 01-27-2017 11:18 AM
    board, check, cnc, set, signal
    • Replies: 0
    • Views: 456
    01-27-2017, 11:18 AM Go to last post
  7. Mach 3, C11 BOB questions.

    Started by vz58‎, 12-10-2016 11:04 AM
    c11, input, led, mach, set
    • Replies: 1
    • Views: 449
    12-11-2016, 02:31 PM Go to last post
    • Replies: 0
    • Views: 197
    11-30-2016, 01:29 PM Go to last post
    • Replies: 2
    • Views: 651
    09-08-2016, 11:36 PM Go to last post
  8. KL8060 probleme

    Started by habibmgh‎, 08-19-2016 01:03 PM
    100khz, diffrent, kl-8056d, kl8060, product
    • Replies: 0
    • Views: 288
    08-19-2016, 01:03 PM Go to last post
  9. KL-6050 Stepper Driver Frustration

    Started by tjp912‎, 06-22-2016 10:00 PM
    3 Pages
    1 2 3
    cnc, electrical noise, kl-6050, motor driver, oscillation
    • Replies: 30
    • Views: 1,629
    06-24-2016, 02:37 PM Go to last post
  10. Limit Switch Help for Controller Box

    Started by Ron2d‎, 06-19-2016 06:21 PM
    box, cnc, controller, limit, wired
    • Replies: 0
    • Views: 429
    06-19-2016, 06:21 PM Go to last post
    • Replies: 6
    • Views: 737
    06-13-2016, 06:51 PM Go to last post
  11. KL - 4030 + Nema 24 8 lead Wiring Help

    Started by twwilson1‎, 04-27-2016 11:32 PM
    • Replies: 0
    • Views: 740
    04-27-2016, 11:32 PM Go to last post
  12. Wiring for KL23H251

    Started by AR1911‎, 11-14-2015 11:02 PM
    • Replies: 9
    • Views: 1,271
    02-10-2016, 11:53 PM Go to last post
  13. Help with KL-1212 (or 6090)

    Started by KLJ‎, 04-12-2013 12:22 PM
    down, then
    • Replies: 4
    • Views: 1,440
    02-10-2016, 10:51 PM Go to last post
  14. Newbie- C10 breakout board with VFD using MACH3

    Started by albert_chuy‎, 02-10-2016 01:08 AM
    • Replies: 0
    • Views: 606
    02-10-2016, 01:08 AM Go to last post
  15. SW4 Standstill Current

    Started by APinSoFla‎, 03-04-2013 05:25 PM
    1-3, sub
    • Replies: 2
    • Views: 1,387
    12-29-2015, 05:31 AM Go to last post
  16. Newbie- Power to C41

    Started by igodwin‎, 12-12-2015 09:11 PM
    • Replies: 0
    • Views: 585
    12-12-2015, 09:11 PM Go to last post

Page 1 of 24 1234 11 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 6 users browsing this forum. (1 members & 5 guests)

  1. JopC

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands