PDA

View Full Version : Need Help! Editing teksoft procam Heidenhain post

RMARCH
01-20-2009, 09:57 PM
Hi,

I was wondering if someone could help me out.
My problem is when my Procam2000 generates a program it does not input The X, Y Value of the CC of the arc center when one of the axises stays the same as the previous arc.

So my control gives me an error.

Example:

0 BEGIN PGM 0001 INCH
1 TOOL DEF 1 L+0 R.25
2 TOOL CALL 1 Z S3000
3 L X-.3169 Y+.6908 RL F3999 M03
4 L Z+.1 R0 F3999 M
5 L Z-.27 R0 F200 M
6 CC X+0. Y+.52
7 C X+.3169 Y+.6908 DR- RL F100 M
8 CC Y+0. X_______
9 C X+.6908 Y+.3169 DR- RL F100 M
10 CC X+.52 Y______
11 C X+.6908 Y-.3169 DR- RL F100 M
12 CC X+0. Y________
13 C X+.3169 Y-.6908 DR- RL F100 M
14 CC Y-.52 X________
15 C X-.3169 Y-.6908 DR- RL F100 M
16 CC Y+0. X _________
17 C X-.6908 Y-.3169 DR- RL F100 M
18 CC X-.52 Y ____________
19 C X-.6908 Y+.3169 DR- RL F100 M
20 CC X+0. Y _________
21 C X-.3169 Y+.6908 DR- RL F100 M
22 L Z+.1 R0 F3999 M
23 STOP M25
24 STOP M02
25 END PGM 0001 INCH



Thanks
Ray
RMARCH
01-22-2009, 08:00 PM
Need Help PLEASE
bert01980
01-23-2009, 05:07 AM
Hallo...
i give one help!!!
RMARCH
01-23-2009, 06:39 AM
The Post processor is for the TNC2500 Control.
Nandop
04-24-2009, 02:08 PM
Still looking for?
I have the post for TNC2500 ISO format.
Let me know.
Nandop.
RMARCH
04-24-2009, 02:29 PM
Hi Nandop,

Thanks for offering your post but i already got one that works.

Thanks Again !!!
RMARCH
06-18-2009, 04:02 PM
Still looking for?
I have the post for TNC2500 ISO format.
Let me know.
Nandop.

Hi Nandop,

Yes, i am still looking for a Procam TNC2500 ISO Format post.
Can you please send it to : RMarch1@comcast.net

I am also looking for post for TNC2500 conversational. I have one now but it doesn't do Arc's & Circles Correct.

Example:

0 BEGIN PGM 0001 INCH
1 TOOL DEF 1 L+0 R.25
2 TOOL CALL 1 Z S3000
3 L X-.3169 Y+.6908 RL F3999 M03
4 L Z+.1 R0 F3999 M
5 L Z-.27 R0 F200 M
6 CC X+0. Y+.52
7 C X+.3169 Y+.6908 DR- RL F100 M
8 CC Y+0. X_______
9 C X+.6908 Y+.3169 DR- RL F100 M
10 CC X+.52 Y______
11 C X+.6908 Y-.3169 DR- RL F100 M
12 CC X+0. Y________
13 C X+.3169 Y-.6908 DR- RL F100 M
14 CC Y-.52 X________
15 C X-.3169 Y-.6908 DR- RL F100 M
16 CC Y+0. X _________
17 C X-.6908 Y-.3169 DR- RL F100 M
18 CC X-.52 Y ____________
19 C X-.6908 Y+.3169 DR- RL F100 M
20 CC X+0. Y _________
21 C X-.3169 Y+.6908 DR- RL F100 M
22 L Z+.1 R0 F3999 M
23 STOP M25
24 STOP M02
25 END PGM 0001 INCH

When the CC is The same as the one before my post doesn't output any value but the control wants one.


Thanks so much !!!
Ray