I am working on writing a post for a Mits FA controller. Can someone please take a look at the code and let me know what I am doing wrong or codes that are need. Thanks

%
L1000 /
(MACHINE,MITSUBISHI,FASeries,)
(CREATED-MON.,10/20/2008,01:52PM,)
N0001 M122
N0002 G90
N0003 G92 X1.5 Y1.5
N0004 WIRE THREAD M78 M78
N0005 M80 M82 M84
N0006 A0.
N0007 E1221 H1=.005 A5.
N0008 G01 G42 X1. Y1.5 F.05
N0009 M90
N0010 G02 X2. Y1.5 I.5 J0.5.
N0011 G02 X1. Y1.5 I-.5 J0.
N0012 G01 G40 X1.5 Y1.5 M91
N0013 A0.
(FEATURE,1,CNT2X,SKIM,1,CUT,REVERSE)
N0014 E002 H1=0. A0.
N0015 G01 G41 X1. Y1.5
N0016 M90
N0017 G03 X2. Y1.5 I.5 J0.0. F.03
N0018 G03 X1. Y1.5 I-.5 J0.
N0019 G01 G40 X1.5 Y1.5 M91
N0020 A0.
N0021 M00
N0022 CUT WIRE
N0023 M02
%

Hi,

your NC code should look like the following:



%
L1000 /
(MACHINE,MITSUBISHI,FASeries,)
(CREATED-MON.,10/20/2008,01:52PM,)
N0001 M122 (Not sure what this code is at the moment)
H01 = .005 (OFFSET REGISTER 1)
H02 = .004 (OFFSET REGISTER 2 OR WHATEVER YOUR SKIM OFFSET SHOULD BE)
N0002 G90
N0003 G92 X1.5 Y1.5
N0004 M20 (WIRE THREAD)
N0005 E1221 F0.5
N0006 M78 M78 (2 STAGE TANK FILL)
N0007 M80 (FLUSHING)
N0008 M82 (WIRE FEED)
N0009 M84 (EDM POWER) (SEPARATE THEM ALLOWS THE SPOOL TO STOP BOUNCING)
N0010 G01 G42 X1. Y1.5 A5.0 H01 M90
N0011 G02 X2. Y1.5 I.5 J0.5.
N0012 G02 X1. Y1.5 I-.5 J0.
N0013 M00 (SLUG STOP - IDEALLY YOU SHOULD ALSO HAVE A GLUE STOP TOO 1MM BEFORE THIS GEO POSITION)
N0014 G01 G40 X1.5 Y1.5 A0. M91
(FEATURE,1,CNT2X,SKIM,1,CUT,REVERSE)
N0015 E002 F.03
N0016 M80
N0017 M82
N0018 M84
N0019 G01 G41 X1. Y1.5 H02 M90
N0020 G03 X2. Y1.5 I.5 J0.0.
N0021 G03 X1. Y1.5 I-.5 J0.
N0022 G01 G40 X1.5 Y1.5 A0. M91
N0023 M21 (WIRE CUT)
N0024 M02
%

I haven't checked your geo but above is pretty much what our machines work well with and we have a mix of FA an CX. We also have other G codes in but you may not need them as it might confuse what you're trying to achieve.

HTH

Roy.