I have a few hundred parts that need five ops on.c' drill, 2 different size drills, c' bore and tap. I want to set them up in three vises and use fixture offsets. But i want to run all three with c' drill then next tool and so on.will this work.4020 FADAL 88HS CONTROL
L0100
xxxx
xxxx
xxxx
m17
m30
L0200
xxx
xxx
xxx
m17
m30
etc
G00 G17 G40 G70 G80 G90
G54
t1m6
L0101
g56
L0101
G57
L0101
G00 G17 G40 G70 G80 G90
G54
T2M6
L0201
G56
L0201
G57
L0201
ETC.

%
O1* 3 FIXTURE DRILL, TAP, AND C-BORE PROG
* X0 Y0 CENTER Z0 TOP OF MATERIAL
* T1 CENTER DRILL
* T2 .1875 DRILL
* T3 .201 DRILL
* T4 1/4-20 CUT TAP (G84)
* T5 .3125 ENDMILL (C-BORE )
L100
G81X0Y0Z-.1R.1F20.
X2.
G80
G0Z1.
M17
L200
G83X2.Y0Z-.5R.1Q.1F20.P.01
G80
G0Z1.
M17
L300
G83X0Y0Z-.75R.1Q.1F20.P.01
G80
G0Z1.
M17
L400
G84X0Y0Z-.5R.4Q.05F500.
G80
G0Z1.
M17
L500
G82X2.Y0Z-.3125R.1F15.P250.
G80
G0Z1.
m17
m30
G00 G17 G40 G70 G80 G90
M6T1
M3S6500
X0Y0G54
H1Z.1M7
L101
g56
Z.1
L101
G57
Z.1
L101
G0Z3.
M5M9
G49Z0
M1
G00 G17 G40 G70 G80 G90
M6T2
M3S6500
X2.Y0G57
H2Z.1M7
L201
X2.Y0G56
Z.1
L201
X2.Y0G54
Z.1
L201
G0Z3.
M5M9
G49Z0
M1
G00 G17 G40 G70 G80 G90
M6T3
M3S6500
X0Y0G54
H2Z.1M7
L301
X0Y0G56
Z.1
L301
X0Y0G57
Z.1
L301
G0Z3.
M5M9
G49Z0
M1
G00 G17 G40 G70 G80 G90
M6T4
M3S500
X0Y0G57
H4Z.4M7
L401
X0Y0G56
Z.4
L401
X0Y0G54
Z.4
L401
G0Z3.
M5M9
G49Z0
M1
G00 G17 G40 G70 G80 G90
M6T5
M3S2500
X2.Y0G54
H5Z.1M7
L501
X2.Y0G56
Z.1
L501
X2.Y0G57
Z.1
L501
G0Z3.
M5M9
X0Y0E0
G49Z0
M1
G00 G17 G40 G70 G80 G90
M6T1
M2
%

I do this all the time, using 4 parts in 2 vises..and I use the fixture offset E 'cause it's easier to recognize, I can number each part with a simple 1,2,3,4, and, well, I'm just used to it.

It looks something like this:

....program definitions.....

M17
M30
G0 X0 Y0 E1
L101
G0 X0 Y0 E2
L101
G0 X0 Y0 E3
L101
G0 X0 Y0 E4
L101
G0 X0 Y0 E1
L201
G0 X0 Y0 E2
L201
G0 X0 Y0 E3
L201
G0 X0 Y0 E4
L201
G0 X0 Y0 E1
L301
G0 X0 Y0 E2
L301
G0 X0 Y0 E3
L301
G0 X0 Y0 E4
L301
G0 X0 Y0 E1
L401
G0 X0 Y0 E2
L401
G0 X0 Y0 E3
L401
G0 X0 Y0 E4
L401
M9
H0 Z0 M5
G0 G90 X0 Y0 E0
M2
%

works great thanks

works great thanks

Which one?

I used the first one