I have recently purchased bobcadcam v21 . I recieved a model of a part that was drawn in solidworks. Is there anyway that i can create a toolpath from the solidworks model. Any help will be appreciated.

Also, I'm Iwant to run program on Matsuura 760v / yasnac mx1 control. Have to run DNC, Anyone know how to run from pc.


thanx much,

REG

There are several standalone CAM's out there. MeshCAM comes to mind. But, not being a solidworks user, I can't be of more help and recomend any specific program or method to do what you want.

thanx sdantonio, but due to spending cutbacks i'm stuck with BCC

BCC is also much less expensive then SW. I would bet that if the file was small enough to email then someone here who new more about file conversions that I would change it from slprt to something BCC can read for you. I'm not sure I would use the word stuck though, BCC is a very good program from what I hear. I'm just lucky enough to have the other stuff at work.

Some of the cams are free, others have free trials. You might want to check out here witha guy called 10bulls. He just wrote a free cad/cam system. I don't know if it will read SW, but it may be worth a try.

I have recently purchased bobcadcam v21 . I recieved a model of a part that was drawn in solidworks. Is there anyway that i can create a toolpath from the solidworks model. Any help will be appreciated.

Also, I'm Iwant to run program on Matsuura 760v / yasnac mx1 control. Have to run DNC, Anyone know how to run from pc.


thanx much,

REG

Reg,

BCC V21 will open a SW File (*.sldprt)

Wether it is a Solid Model or Wire Frame BCC will create Tools Paths. It just takes a little time to get used too.

Here are two other Forums full of BCC Users

http://216.117.147.20/bobcadsupport/forums/index.php

This one is Sorin's Forum(CAD/CAM Trainer.com). In case you didn't know, Sorin is the Official BobCAD/CAM Trainer. Register on his site. You will get a Password to his FREE Video Tutorials. As an added plus, he is a Real Machinist that Applies the Software to Real Machining Situations.

http://cadcamtrainer.com/forums/index.php

Cheers :)

Of Bcc. The Original V21 Did Only Open Up Sldprt Files From Solidworks 2006.

hehe...

Just have the Solidworks user export the SLDPRT of what you need to machine. The whole assembly, if it is one, is not needed and will only cause problems.

Next check the Videos, Manual and forums that mr. Axis has suggested.

Finally CALL SUPPORT...they will be able to provide more efficient assistance than any forum, of course only during regular business hours.

Regards
OH yeah I forgot a quote...
"All men hate the wretched. How then must I be hated who am miserable beyond all living things..." -M. Shelley "Frankenstein"

hehe...
Next check the Videos, Manual and forums that mr. Axis has suggested.

Finally CALL SUPPORT...they will be able to provide more efficient assistance than any forum, of course only during regular business hours.

Regards
OH yeah I forgot a quote...
"All men hate the wretched. How then must I be hated who am miserable beyond all living things..." -M. Shelley "Frankenstein"

You forgot to post the Business Hours.:eek:

8am to 5pm Eastern Time Monday through Friday;) :rainfro:

BCC Support is your best bet in getting help for this issue.:)

thanx tobyaxis, sorry i didn't answer sooner .been really busy at the shop. I did get the solidpart to load and i got a toolpaths.

thanx again

Reg

thanx tobyaxis, sorry i didn't answer sooner .been really busy at the shop. I did get the solidpart to load and i got a toolpaths.

thanx again

Reg

COOL!!!!!! Congrats!!!!!! :rainfro:

You can check these forums out too:)

http://216.117.147.20/bobcadsupport/forums/
http://cadcamtrainer.com/forums/index.php